Nexa CFR-2027, Руководство по эксплуатации, Страница: 3 / 5

1. Install CFR-2027 into lamp holder
2. Switch ON the mechanical switch.
3. Following switch mechanical switch OFF/ON 6 times ending last at ON mode, lamp starts to slow flash.
This will enter learning mode.
4. On transmitter press ON button to send ON signal to CFR-2027 receiver.
5. CFR-2027 light bulbs will quick flash 8 times to confirm code is stored.
6. After the 8 times quick flash, the lamp will continuously flash slowly (returning to learning mode).
7. In the meantime, user can use another transmitter to make receiver memorize another code. CFR-2027
receiver can memorize up to 6 memories.
NOTE: Operating both remote control and mechanical switch at the same time
To operating with a remote control, make sure the mechanical switch is turned ‘ON’
If the light is switched ‘OFF’ by a remote control, remember the mechanical switch is still at ‘ON’ status.
So next time switching ‘ON’ with the mechanical switch remember to switch twice from ‘OFF’ to ‘ON’
※
REMARK
※

If during learning mode no RF or manual button signal is record then CFR-2027 receiver will stop
flashing after 20 seconds OR either switch OFF the mechanical switch. This will deactivate the learning
mode.

For the convenience of setting up multiple transmitters, 20 seconds will recount again after each
completed setup.
Nast
avenie
kód
ov (O
br.2)
Priblíž
te v
ysielač
nap
r. LY
CT-505
do
blízkosti
prijímača
a jeden
krát
stla
čte
tlačidlo u
čenia kód
ov na prijímači.
LED indi
kátor začne pomaly bli
kať,na
vysielači stla
čte tlačidlo
“I”.
Svietidlo pripojené k prijímaču dva
krát bli
kne p
re po
tvrdenie prijatia kód
u.
LED indi
kátor na prijímači p
restane bli
kať,kód je prija
tý.
•
(Zapamätaj
te si tlačidl
o,k
toré s
te
zvolili na nap
rog
ram
ovanie do prijímača)
•
Vysielač a prijímač sú nap
rog
ram
ované - spá
rov
an
é.
Zmena alebo
vymazanie
kódu:
•
V
ymazanie jedného
kó
du:
(Ob
r.3)
Stla
čte
tlačidlo
uč
enia
kód
ov
na
prijímači
jeden
krát,
LED
indi
kátor
začne
pom
aly b
lika
ť.
Stla
čte
vybrané tlačidlo na
vysielači
“0
” ,vybra
ný kód sa
vyma
že.
Svietidlo
pripojené
k
prijímaču
dva
krát
bli
kne
pre
po
tvrdenie
vymazania
kódu .LED p
restane bli
kať.
Rovnako postupuj
te pri
vymazaní ďalších kód
ov.
V
ymazanie
c
elej pam
ä
te:
(Ob
r.4)
K svietidlu
230V/50Hz
K svietidlu
230V/50Hz
Ob
r.2
Ob
r.3
Nul
ový
vodič
Nul
ový
vodič
Nul
ový
vodič
Nul
ový
vodič
Fáz
ový
vodič
Fáz
ový
vodič
Fáz
ový
vodič
Fáz
ový
vodič
230V/50Hz
230V/50Hz