Call us for more information on +44 (0)1732 360095
5
This Installation Manual is for the Victron MultiPlus Inverter/Charger unit 12/3000/120. The maximum pump size
that can be connected to these units is 750W:
• Newton CP750
• Newton NP750
• Newton SP750 Cutter
Pumps of 150, 250 & 400W can also be used with this unit but smaller MultiPlus Compact Inverter/Chargers are
available for less powerful pumps. For confirmation of the correct size of Inverter for the Newton pump being
used please refer to the Victron Inverters Data Sheet.
TYPICAL DETAILS
Below is a typical setup as part of a Newton System 500 waterproofing system which can be used as a quick
install schematic. If a control panel is not used the pumps will be automatic versions and each pump will have
just one cable coming up from the conduit. Connect pump 1 directly to the mains and pump 2 to the MultiPlus.
Example 1
- 2 x Automatic Pumps - No Pump Control Panel - No Inverter/Charger Control Panels
+
MultiPlus
12
charger
inverter
victron energy
B L U E P O W E R
A C transfer capacity: 1x 50 A + 1X30A Inverter 230V
battery charger
sinewave inverter
transfer switch
powerassist
parallel
connectable
three phase
connectable
mains on
bulk
absorption
float
Inverter on
overload
low battery
temperature
www.victronenergy.com
on
off
charge only
VOLT
3000 120
VA
AMP
Batt ery
B efore charging read the i nstructi ons. For i ndoor use onl y. Disconnect
the suppl y before maki ng or breaki ng the connections to the battery.
WARNING: E xplosive gases, prevent flames and sparl s, provi de
adequate venti l ati on duri ng chargi ng. Charge lead-acid or Li-lon batteries
onl y.
-
Newton MultiPlus 12/3000/120
Newton High Water Alarm
DC Battery
Temp - & Temp +
pum
p one
pum
p two
Pumps compatible with
MultiPlus 12/3000/120
CP750/NP750/SP750 Cutter
For Battery dimensions
please see drawings
prefixed Batt
AC1
input
AC1
output
The Victron MultiPlus 12/3000/120
battery back up system. Installed in
conjunction with Newton's System 500
pumping systems.
The Victron system provides an
Inverter/Charger function ensuring
water can still be removed in the event
of a power outage.
Additional batteries can be added of
varying sizes and power to provide
longer protection.
For Newton system 500 pumping
Specification's please contact
Newton's technical team on
01732 360095 or enquire about using a
Newton specialist contractor.
In addition upgrades can be made to
offer extra peace of mind and further
reduce risk.
Newton Dialler - requires a BT
Telephone line.
Victron Battery monitor
Victron blue power panel
Newton System 500
Titan-Pro White Automatic pumping
System used with Newton System
500 waterproofing.
Section
To access the details mentioned above,
relevant NBS Clauses, product data and
MSDS sheets, please use this hyperlink:
Drawing Support
Checked by
Designed by
Date
Scale
Notes
Ref
Drawn by
Original Ref
NOTE: This is a waterproofing detail. For the design of the structure, please use a professional designer. We strongly recommend that Newton waterproofing systems are installed by our NSBC registered contractors who will guarantee,
insure and accept liability for both the design and the installation of our systems Please refer to product data sheets before installation of our products. John Newton reserves the right to update drawings.
NEWTON
Waterproofing Systems
17 - 19 Sovereign Way, Tonbridge, TN9 1RH
Tel: 01732 360095 Fax: 01732 359033
www.newton-membranes.co.uk - [email protected]
(EST. 1848)
Not to scale
29/04/2014
V3 - 03
AJB
XXX
AJB
INFORMATION, DIMENSIONS AND SAFETY INSTRUCTIONS
INVERTER SIZING AND TYPICAL DETAILS
