Newland HR3260-CS Скачать руководство пользователя страница 36

Страница: 36 / 165

【

Enter Setup

】

【

Exit Setup

】

Transmit NGR Message

Scan a barcode below to select whether or not to transmit a user-defined NGR (Not Good Read)

message when a barcode is not decoded.

【

Transmit NGR Message

】

【

Do Not Transmit NGR Message

】

Edit NGR Message

To edit an NGR message, scan the

Edit NGR Message

barcode and the numeric barcodes

corresponding to the ASCII values (decimal) of desired character(s) and then scan the

Save

barcode.

An NGR message can contain 0-7 characters (ASCII value of character: 0-255).

【

Edit NGR Message

】

Set the NGR message to “!ERR” (0x21, 0x45, 0x52, 0x52):

1. Scan the

Enter Setup

barcode.

2. Scan the

Edit NGR Message

barcode.

3. Scan the num

eric barcodes “2”, “1”, “4”, “5”, “5”, “2”, “5” and “2”. (See the

Digit

Barcodes

Appendix

)

4. Scan the

Save

barcode. (See the

Save/Cancel Barcodes

Appendix

)

5. Scan the

Exit Setup

barcode.

Содержание HR3260-CS






































































































































































Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды

Newland HR3260-CS, Руководство пользователя

Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды