New Yorker Link NY119SL Скачать руководство пользователя страница 9

9

WATER TEMPERATURE CONTROLS

A periodic inspection of the operating controls, heat exchanger and wiring should be made by qualified ser

-

vice personnel. Temperature of the water should be tested periodically at the faucet to be sure thermostat 

is working properly. 

 

 

TEMPERATURE ADJUSTMENT

The TPI comes with a factory set temperature setting of 0°F and differential 

setting of 0°F.  Any temperature adjustment of the thermostat must be made  

by qualified service personnel, as shown below.

WARNING: See SERVICE INFORMATION Water Temperature Regulation, 

regarding safe water temperature before proceeding.  Hot water can cause 

scalding injuries.

1.

  Shut off or disconnect all electrical supply to heater.

2.

  Remove cover to TPI control.

3.

  Adjust right side lever to the desired temperature.  Moving lever down will  

  decrease temperature.  (See figure at right and TPI Diagram 1).

 

NOTE: Markings on slide are approximate.  Check temperature at faucet  

  to ensure safe operating temperature.

4.

  Adjust left side lever to the desired differential. (See figure at right and TPI  

  Diagram ) The TPI thermostat will call for heat when the tank temperature  

  has fallen to the set differential degrees below the temperature set point.

5. 

Reattach cover.

6.

  Reconnect electrical supply.

7.

  Check faucet temperature to verify desired temperature is achieved. 

 

In order to set the temperature above 40°F

 {NOT RECOMMENDED}

 you must remove the SCALD  

DANGER label attached to the temperature slide. 

 

Caution: Do not increase temperature above 140°F without a properly installed mixing valve in the 

system – See Water Temperature Regulation and SCALD WARNING.

 

 

Indicator Light operation:

The TPI thermostat has an integral indicator light at the top of the case.  

(See TPI Diagram 1 or Inside Cover of TPI)

Indicator light will come on (Green) when TPI is powered.
When TPI is calling for heat, the Indicator light will blink. 

When TPI is satisfied, the Indicator light will be solid.

During normal operation, Indicator light is Green.

If TPI detects a failure, Indicator light will flash Red.  Replace TPI.

 

 

EMERGENCY

Should the heater be subject to flood, fire or other damaging conditions, turn the power and water to the 

heater off.  

DO NOT

 place water heater in operation again until it has been thoroughly checked by qualified 

service personnel.

Temperature

Differential

Pump/TT

24v

LED

flashing green = calling for heat

solid green = at temperature

red = error

20°

15°

10°

160°
150°
140°
130°
120°
110°

Probe

Содержание Link NY119SL

























Отзывы: