manualshive.com logo in svg

New lift FST, Руководство пользователя

Поделиться
Скачать
New lift FST Скачать руководство пользователя страница 123

1   Menu tree

1.4   MAIN MENU – Config

FST_HB.EN04/03 

 121

EAZ Configuration –

Display Dimming

Dimming the LON display EAZ-256 when the car light is off to 
reduce energy consumption. This function can be activated 
separately for in-car and landing indicators.

-

00000000: Dimming function off.

-

00000001: Only in-car indicators are dimmed.

-

00000010: Only landing indicators are dimmed.

-

00000011: All indicators (in-car and landing) are dimmed.

00000000 ...
11111111

Chime Functions –

Chimes Enabled

Chime sounds for car and/or landing calls.

YES
NO

Chime Functions –

Chime Duration

Impulse length of the chime trigger signal.

0 ... 5 sec

Chime Functions –

Chime Trigger

Distance of the car from the levelling position of the target floor 
that triggers the chime.

0 ... 9999 mm

Chime Functions –

Chime when in floor

The chime also sounds when the car doors are closed and the 
car is already at the target floor when the lift is called with a 
landing call.

YES
NO

Chime Functions –

Landing Chimes

Chimes sounds for landing and/or in-car calls.

Landing calls
Car+Landing calls

ID –

Lift ID-Number

Identifies the FST-Controller in group operation.
The setting must correspond to the jumper settings (JK1, JK2 
and JK4) on the FSM Car Control Module (see “Jumpers” on 
page 59) and the FPM Car-Operate-Panel (“Jumpers” on 
page 66)! If this fails the system will be shut down with 

DRM-

CAR COMMS FAIL

 (see “

DRM–CAR COMMS FAIL

” on 

page 155). Single lifts are always set to Lift A.

A ... H

ID –

Lift ID-Name

Location, identification of the FST-Controller for modem, 
remote data transmission and PAM (LMS).

20-digit ASCII

ID –

NEW-Factory No.

NEW LIFT factory number of the FST-Controller (set in the 
factory).

20-digit ASCII

ID –

Lift factory no.

Lift manufacturer’s factory number of the system.

20-digit ASCII

ID –

Project-Code

Code number of a project specific software version. Only 
issued for special projects, do not change!

000000 ....
999999

Group Settings –

GST-Menu

See GST Manual.

Group Settings –

Lift ID-Number

See 

Lift ID-Number

.

A ... H

Group Settings –

Group Member

Integrate FST-Controller in a GST Group Controller (see GST 
Manual).

YES
NO

Group Settings –

Group Floor Offset

Floor offset in relation to the lowest floor in the group (see GST 
Manual).

0 ... 15

Group Settings –

Flr Offset-Car

The value set in 

Group Floor Offset

 is the lowest floor 

for the position indicator in the car (if not set the value „0“ will 
be used, see GST Manual).

YES
NO

Group Settings –

Flr Offset-Landing

The value set in 

Group Floor Offset

 is the lowest floor 

for the landing position indicators (if not set the value „0“ will 
be used, see GST Manual).

YES
NO

Group Settings –

ADM-Bus Mask-1

Allocation of the FST to the individual bus lines of the group in 
normal mode (see “ADM-Bus Masks” on page 127 and the 
GST Manual).

00 ... FF

Menu item

Description

Setting range

Содержание FST















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды