New lift FST Скачать руководство пользователя страница 157

Страница: 157 / 174

6 Error List

6.4 Error messages

FST_HB.EN04/03

155

DRM–ENCODER FAILURE

Plausibility testing of car position
with the encoder is faulty.

Reset

TEST MENU – Fault

Reset

The encoder is faulty.

Check electric connection of
the encoder.

During commissioning: Check
direction of rotation of the
encoder and carry out “Set
Floor 0”.

DRM–CAR COMMS FAIL

Communication between the FST-
Controller and the FSM Car Control
Module is faulty.

Plug-in connections of the
trailing cable are not plugged
or loose.

Rupture in trailing cable.

Car Control Module FSM
faulty.

Check jumper position on the
car control module (see
“Assigning the car in group
mode” on page 60).

DRM–END FLOOR SPEED

Reset

TEST MENU – Fault

Reset

The delay control circuit at the
top and bottom limits has
triggered (see “End-Sw.Speed
Mon.” on page 114).

DRM–MISSING ZONE

No zone message available.

Reset

TEST MENU – Fault

Reset

The car has reached a levelling
position but does not receive a
zone message from the A6
Safety Circuit.

Check A6 Safety Circuit and
zone solenoids.

DRM–BRAKE FAILURE

The brakes do not react or cannot be
released.

Reset

TEST MENU – Fault

Reset

The brake does not release
even with pre-selection active

The brake does not close even
with the car stopped.

Monitoring via input VSM X4.7
(see “Brake Monitoring” on
page 113).

DRM–MOTOR FAILURE

Temperature monitoring of the drive
has triggered.

Motor overheated.
Monitoring via input VSM X4.5
(see “Motor Monitoring” on
page 113).

DRM–FORCED STOP

The input signal “Forced Stop” on a
programmable input has been
active. The car is shut down on the
floor with the door open.

Please refer to the system
specific wiring diagrams for
information on which signal has
triggered the forced stop. Also
see “Programmierbare Ein-/
Ausgänge” on page 155).

DRM–EMERG.LIMIT SW

Exceeding the top floor according to
EN 81 (for hydraulic lifts).
Reset

TEST MENU – Fault

Reset

The top emergency limit switch
has triggered. The contact is
sampled by terminal VSM X1.5
(“TC”).

DRM–DOOR FAILURE

The car door cannot be moved.
Reset

TEST MENU – Fault

Reset

Door control is active but the car
door does not move. The
controller shuts down the system
(see “Allow DRM-Door” on
page 145).

Code

Message

Description

Reason

Содержание FST















































































































































































Результаты поиска

Содержание FST

Отзывы:

Похожие инструкции для FST

Бренды по названию

Популярные бренды

New lift FST, Руководство пользователя

Результаты поиска

Содержание FST

Отзывы:

Похожие инструкции для FST

Бренды по названию

Популярные бренды