manualshive.com logo in svg

New Leader L4000G4, Руководство пользователя

Поделиться
Скачать
New Leader L4000G4 Скачать руководство пользователя страница 3

- 4 -

www.NewLeader.com

(800) 363-1771

313967-I

SPREAD PATTERN

Header

Spread Pattern

Spinners

NOTICE!

Spinner discs and fins must be kept clean and polished.  Even a small build-up on a spinner 

fin can significantly affect the spread pattern.  Rusty, rough, bent or worn fins will produce 

poor spread patterns.

In general, critical spinner speed will fall somewhere between 600 and 900 RPM.  Spinner speed is adjusted 

by changing the settings in the controller.  Proper spinner speed adjustment is critical in obtaining optimal 

spread patterns.  The best spinner speed to use will depend entirely on the material being spread, and 

must be determined by testing.  

Spreader Preparation

The spreader to be tested must be in good mechanical condition and properly adjusted. Refer to operator’s 

manual for details.

All damaged and worn parts must be replaced.  Spinner discs and fins must be free of any material build-

up, rust or paint.

Fill the hopper with the material to be spread.  Run the material out to the end of the conveyor.

Set the feedgate and the in-cab controller to deliver the required rate per acre.  Make sure the feedgate 

is level and the indicator reflects the actual gate opening measured by standing a tape measure vertically 

in the material.

  

NOTE:

  Do not match slope of endgate when making this measurement. Measurement must be 

perpendicular to conveyor.

Adjust the spinner assembly by turning the crank or, if an actuator is installed, change the setting in the 

controller.  To begin testing, position the spinner according to the chart below.  

Содержание L4000G4











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды