New Japan Radio NJT8103 series Скачать руководство пользователя страница 18

Страница: 18 / 21

NJT8103 series Instruction Manual

Page 18

Step 2:

Use self-amalgamating tape to seal connector and cable entry

points from the connector to the cable sheath.

Only input a voltage within the range indicated in specified

voltage.

DO operate at the input voltage of +12 to +30 V DC power at

the coaxial connecter on the Unit.

DO NOT input an IF signal over the range of +13 dBm

maximum and a reference signal within the range of -5 to +5

dBm.

6.2. Connecting Modem

The Unit is connected the modem.

6.2.1. Connecting Coaxical Cable.

The Unit receives the reference and the IF signal and is required to supply

+12 to +30 V DC power from the modem via coaxial cable.

IM-T8103 Rev.01

When connecting the coaxial cable from the modem, follow the following

steps:

Step 1:

Connect the coaxial cable with the N or F-type male connectors

to the coaxial connecter equipped with the Unit which is shown

in a figure below under 0.68 to 1.13 N

・

m torque.

Location of Coaxial Connector

Supplied the IF/Ref./DC Power

via Coaxial Cable

Содержание NJT8103 series






















Результаты поиска

Содержание NJT8103 series

Отзывы:

Бренды по названию

Популярные бренды

New Japan Radio NJT8103 series, Инструкция по эксплуатации

Результаты поиска

Содержание NJT8103 series

Отзывы:

Бренды по названию

Популярные бренды