2 - SAFETY INFORMATION
• Be sure you know the position and function of each
control. Incorrect operation of the controls can cause
serious injuries.
• Check all controls and safety devices in a safe, open
area before starting work.
• Keep away from dangerous areas such as ditches,
overhangs, rocky areas, etc. Make a survey of the
work-site and determine the possible dangers before
using the machine.
• Before parking the machine, make sure that the ground
is stable. Plan the work-site so that the ground is flat,
hard and level.
• Before moving the machine to work in a new area, walk
around to determine all possible causes of accidents
there. Holes, obstacles, debris, and other danger risks
in the working area can cause serious injury.
• Be ready to meet emergencies. Always carry a first aid
kit and if possible, fire extinguisher (not supplied) within
easy reach on board. Make sure the fire extinguisher
is regularly serviced in conformance with the manufac-
turer's instructions.
• Check the fastening of the main components: counter-
weight, swing bearing, and operator's compartment. In
the event of problems, consult your NEW HOLLAND
CONSTRUCTION Dealer.
• Make sure you understand the symbols used on the
machine safety signs. Keep the signs clean so that they
are completely legible at all times.
• Work out a means of convenient escape from the ma-
chine (emergency exit via the windshield or the rear
window glass) in the event of the machine turning over
or tipping over or the cab door being jammed.
• Make sure you are familiar with traffic regulations and
special safety equipment requirements before trans-
porting this machine on a public highway.
• When loading trucks, never swing the load over the
truck cab.
• Before undertaking any travel on the job site, make sure
the itinerary to be followed is safe. If bridges are to be
crossed, make sure they are capable of supporting the
weight of the machine.
• Always steer round large obstacles such as boulders,
big trees, etc.
Quick coupler (optional)
• Every day, check that the locking bar functions correctly
and that it is not fouled by foreign matter. Clean the
locking system if necessary.
• If you must use the quick coupler with buckets not man-
ufactured by NEW HOLLAND CONSTRUCTION, make
sure the diameter of the pins and the width between
the bucket lugs meet the dimensions needed to fit the
quick coupler (pins, washers, bushings, etc.). Consult
your NEW HOLLAND CONSTRUCTION Dealer.
Operating the machine
• When working on a public highway, use standard traf-
fic signs and take into consideration the working range
of the upperstructure and its attachments. Local or na-
tional regulations stipulate the number, type, and loca-
tion of reflector strips.
• Avoid running the engine in a confined space. If there
is no alternative, proper ventilation must be provided at
all times.
• Do not allow anyone else on the machine. The passen-
ger could fall or cause an accident.
• Never operate the working or travel controls unless you
are properly seated in the operator’s seat with the seat
belt correctly fastened.
• Before starting the engine, check the direction of travel
(in forward drive, the reduction gears should be to the
rear of the machine).
• Do not work near overhead high-voltage electric lines
without checking beforehand that all necessary mea-
sures have been taken to respect the minimum dis-
tances:
Less than 57000 volts:
3 m
(
9.8 ft
).
More than 57000 volts:
5 m
(
16.4 ft
).
• Study the position of any existing pipelines or conduits
before starting work. Electrical cables, gas and water
pipes, and other underground installations can cause
serious injury.
• Always make allowance for working conditions (slop-
ing or rough ground), the site, and weather conditions
when driving the machine.
• Do not allow anyone to stand in the machine working
area. Accidental operation of the upperstructure swing
control or of an attachment control could cause an ac-
cident. Stop all operations until everyone has moved
away.
• Before operating the dozer blade (if equipped) make
sure that there is no one in the working area of the dozer
blade.
• Operate all controls gradually to ensure smooth ma-
chine operation.
• Whenever load handling operations are to be carried
out, it is imperative to adhere strictly to the instructions
given in this manual and local legislation.
• It is forbidden to use the machine to carry out tasks
other than those for which it is intended. Never use the
equipment for sweeping the ground to level out rubble
or push objects (these actions cause transversal stress
on the attachment).
• Stop the engine and remove the ignition key when the
machine is not in use, even for short periods of time.
2-8
Содержание E26C
