NetWave NWK1 Скачать руководство пользователя страница 5

INS_NWK1_NWK2_QS_REV–   07/7/15   PAGE 5

INSTALLATION REQUIREMENTS

CONFIGURING NETWAVE

QUICK START USER GUIDE 

NWK(1,2)

TECH SUPPORT: 1.888.678.9427

Shielded outdoor CAT 5 or better should be used for all out of plant Ethernet connection and should be properly grounded 
through the PoE AC ground. Industrial grade shielded Ethernet cable is recommended to help prevent ESD damage commonly 
experienced with outdoor installations. Visit www.comnet.net/comnet-products/cables

1.  Connect an Ethernet cable from the port labelled as IN on the power Injection Module to either a laptop or a PC LAN port.

2.  Connect the second Ethernet cable from the OUT port on the Power Injection Module to the NetWave LAN port. 

3.  Apply 48 VDC to the Power Injection Module with the provided power supply. You should notice the green LED illuminate in 

the Power Injection Module and the power LED on the NetWave unit.

4.  Set the IP address of the laptop being used to configure NetWave to static and the subnet to 192.168.10.x/24 subnet.

5.  Point the Browser to 192.168.10.100 for the Access Point or 192.168.10.101 for the Client. These are the default addresses.

6.  A login prompt will pop up. Enter: 

ID: 

admin

 

 

Password: 

admin

7.  Select the NETWORK 

»

 Interfaces tab, click on Edit in the LAN settings section to change the IP address of the device. and set 

the desired network settings. 
• Hit Save & Apply 
NOTE:  This will be the network address for the NetWave web server. It is not necessary to set to the same subnet as the 

operating network but it is recommended.

8.  Select the NETWORK -> WIFI tab and set: 

• Wireless mode – Set to AP or Client 
• Country code – Only required if setting up the NW2 and NWK2 (ETSI) models 
NOTE:  It is the user’s responsibility to ensure that the correct country is chosen. ComNet accepts no liability for incorrectly set 

up equipment. 

• Output RF power – if RSSI is greater than -40, it is recommended to reduce RF TX power at the connected remote node.

• Set SSID – if changing from the default setting

•  Channel Spectrum Width – May want to reduce to 20M from the default 20/40M if the 5GHz spectrum is crowded or 

connections across the link are unstable.

• Wireless Security – if changing from default settings

• Hit Save & Apply

Содержание NWK1










Отзывы: