background image

 

 

 

Table of Content 

 

1. Introduction .................................................................................................................................................................. 2

 

2. Appearance ................................................................................................................................................................... 3

 

3. Main Feature ................................................................................................................................................................ 3

 

4. Set up Instruction ......................................................................................................................................................... 4

 

5. Data Report .................................................................................................................................................................. 5

 

5.1 Example of ReportDataCmd................................................................................................................................. 5

 

5.2 Example of ConfigureCmd ................................................................................................................................... 6

 

5.3 Example of Switching Mode ................................................................................................................................ 8

 

5.4 Example of DeadZoneDistance ............................................................................................................................ 9

 

5.5 Example of General Calibration Configuration ................................................................................................. 10

 

5.6 Example for MinTime/MaxTime logic............................................................................................................... 11

 

6. Application ................................................................................................................................................................. 13

 

7. Installation .................................................................................................................................................................. 14

 

8. Comparison between R718PE & R718PE01 ............................................................................................................. 16

 

9. Information about Battery Passivation ...................................................................................................................... 16

 

9.1 To determine whether a battery requires activation ........................................................................................... 16

 

9.2 How to activate the battery ................................................................................................................................. 16

 

10. Important Maintenance Instruction .......................................................................................................................... 17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание R718PE01



















Отзывы: