netsys NP-100SE+/PD Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 25

netsys NP-100SE+/PD Скачать руководство пользователя страница 11

PoE SERIES NP-100SE+/PD USER’S MANUAL Ver. A6

10

Chapter 3.

Installation

3.1 Hardware Installation

This chapter describes how to install the PoE and establishes network connections. You may install the PoE on any level

surface (ex. table). However, please take note of the following minimum site requirements before you begin.

3.2 Pre-installation Requirements

Before the start of actual hardware installation, make sure to provide the right operating environment, including power

requirements, sufficient physical space, and proximity to other network devices that are to be connected. Verify the

following installation requirement:

•

Power requirements:

48VDC / 0.4A

•

The PoE should be located in a

cool dry place

, with at least

10cm/4in

of space at the front and back for

well ventilation.

•

Place the PoE away from

direct sunlight

,

heat sources

, or areas with a high amount of electromagnetic

interference.

•

PD has 5V DC/9V DC/12V DC three kinds of DC power option, You can according to demand purchase of

equipment

•

Check if network cables and connectors needed for installation are available.

Note:

Each of the PD device can only output a DC power, choice of powered device for 5V DC or 9V DC or 12V DC.

«
...
9
10
11
12
13
...
»

Содержание NP-100SE+/PD


























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды