background image

NETIS SYSTEMS CO., LTD.
www.netis-systems.com
MADE IN CHINA

4.Troubleshooting

 How do I restore my netis WF2322 to default settings?

A

  With the router powered on, holding “

Reset

” button on the PoE injector for 8s~10s with a pin to 

     restore it to factory defaults.

Q

 What can I do if my Internet cannot be accessed?

A

 1)  Check to verify the hardware connections are correct. Please refer to the “Hardware Connection” step.

    2)  Refer to 3.1) to set a Static IP address for your PC and connect the WF2322 to your PC.
    3)  Open a web browser and login to http://192.168.1.1
    4)  Re-check your setting
    5)  Reboot the modem first and then netis device. Wait for one minute before you check the Internet again. 
    6)  If Internet access is not available, please connect your computer directly to your modem and try 
        the Internet again. 
If the Internet is still not working, please contact your ISP for further help.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one of the following measures:

·

Reorient or relocate the receiving antenna.

·

Increase the separation between the equipment and receiver.

·

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

·

Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

1. The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) 
    used for this transmitter must not be co-located or operating in conjunction with any other antenna or 
    transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
3. This equipment should be installed and operated with a minimum distance of 20 centimeters between 
    the radiator and your body.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference and  
(2) this device must accept any interference received, including interference that may cause undesired 
operation   

Technical Support

:

USA/ Canada
Toll Free: +1 866 71 network (+1 866 716 3896)
E-mail: [email protected]

Other Regions:
E-mail: [email protected]

P

K

U

M

0

5

6

2

1

Содержание WF2375









Отзывы: