NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTERNATIONAL LTD
Floor 1, Building 3
University Technology Centre
Curraheen Road, Cork,
T12EF21, Ireland
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
August 2019
Use the CLI to configure the IP address
To use the CLI for initial configuration and assign a static or dynamic IP address
to the switch, connect a computer or VT100/ANSI terminal to one of the console
ports on the switch.
1. Depending on the connector type at your computer or terminal, and the port
that you are using on the switch, use one of the following cables, both of
which are included in the product package:
• USB console cable for use with the mini USB console port.
Note:
To use the mini USB port, you must install the USB driver on the
computer. You can download the driver by visiting
netgear.com/support/download/.
• Console cable for use with the RJ-45 RS232 console port.
2. Connect one end of the cable to the appropriate port on the switch and
connect the other end to your computer or terminal.
3. If you connect a computer to a console port on the switch, start a terminal
emulation program:
• On a computer with a Windows operating system, you can use
HyperTerminal or Tera Term.
• On a computer with a Mac operating system, you can use ZTerm.
• On a computer with a Linux operating system, you can use TIP.
4.
If you connect a computer to a console port on the switch, configure the
terminal emulation program to use the following settings: baud rate, 115,200
bps; data bits, 8; parity, none; stop bit, 1; flow control, none.
5. At the user prompt, log in to the switch using the user name
admin
and
press Enter. At the password prompt, do not type a password but press Enter.
You can now use the CLI to manually configure the IP address of the switch,
or to use the ezconfig utility, continue with the next step.
Note:
For information about CLI management, see the CLI reference manual.
6.
At the next command prompt, type ezconfig and press Enter.
The ezconfig utility is now running on the switch.
Netgear Switch) #ezconfig
EZ Configuration Utility
7. Using
ezconfig, set up the basic switch configuration, including
a static IP
address and subnet mask.
8.
Use the switch IP address that is assigned by ezconfig to log in to the switch’s
local browser interface.
Find the IP address assigned by the DHCP server
By default, the switch functions as a DHCP client and gets its IP address from
a DHCP server in the network. To find the assigned IP address of the switch’s
management interface or OOB port, connect a computer or VT100/ANSI
terminal to one of the console ports on the switch.
1. Make sure that the switch is connected to a DHCP server.
2. Set up a console connection with the switch.
For information about setting up a console connection, see Steps 1 through 5
in
Use the CLI to configure the IP address
. After you are logged in and at the
CLI command prompt, continue with the next step.
3. At the command prompt, type one of the following commands:
•
To find the IP address of the management interface, type the
show ip management
command, and press Enter.
•
To find the IP address of the OOB port (which is also referred to as the
service port), type the
show serviceport
command, and press Enter.
The active IP address displays.
4. Use either the management interface IP address or the OOB port IP address
to log in to the switch’s local browser interface.
3. Log in to the local browser interface
Manage the features of your switch through the local browser interface with the
appropriate IP address for your configuration.
Note:
When you access the switch, make sure that it is running the latest
firmware version. To download firmware, visit
.
1. Enter
http://<ipaddress>
in the web browser address field.
A login window displays.
2. Enter
admin
for the user name, leave the password field blank, and click the
LOGIN
button.
The System Information page displays. You can now navigate from this page
to other pages and configure your switch.
For information about using the local browser interface, see the user manual.
You can download the user manual, the hardware installation guide, and other
manuals by visiting
Support
Thank you for purchasing this NETGEAR product. You can visit
https://www.netgear.com/support/
to register your product, get help, access the
latest downloads and user manuals, and join our community. We recommend
that you use only official NETGEAR support resources.
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en
https://www.netgear.com/support/download/
.
(If this product is sold in Canada, you can access this document in Canadian
French at
https://www.netgear.com/support/download/
.)
For regulatory compliance information including the EU Declaration of
Conformity, visit
https://www.netgear.com/about/regulatory/
.
See the regulatory compliance document before connecting the power supply.
Do not use this device outdoors. If you connect cables or devices that are
outdoors to this device, see
https://kb.netgear.com/000057103
warranty information.
