NETGEAR Nighthawk X4S R7800 Скачать руководство пользователя страница 87

Страница: 87 / 160

Display Internet Port Statistics

To display Internet port statistics:

Launch a web browser from a computer or WiFi device that is connected to the network.

Enter http://www.routerlogin.net.

A login window opens.

Enter the router user name and password.

The user name is admin. The default password is password. The user name and password are case-sensitive.

The BASIC Home page displays.

Click the ADVANCED tab.

The ADVANCED Home page displays.

In the Internet Port pane, click the Show Statistics button.

The following information displays:

•

System Up Time. The time elapsed since the router was last restarted.

•

Port. The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each port, the screen displays the
following information:

•

Status. The link status of the port.

•

TxPkts. The number of packets transmitted on this port since reset or manual clear.

•

RxPkts. The number of packets received on this port since reset or manual clear.

•

Collisions. The number of collisions on this port since reset or manual clear.

•

Tx B/s. The current transmission (outbound) bandwidth used on the WAN and LAN ports.

•

Rx B/s. The current reception (inbound) bandwidth used on the WAN and LAN ports.

Manage Your Network

Nighthawk X4S AC2600 Smart WiFi Router

Содержание Nighthawk X4S R7800

































































































































































Результаты поиска

Содержание Nighthawk X4S R7800

Отзывы:

Похожие инструкции для Nighthawk X4S R7800

Бренды по названию

Популярные бренды

NETGEAR Nighthawk X4S R7800, Руководство пользователя

Результаты поиска

Содержание Nighthawk X4S R7800

Отзывы:

Похожие инструкции для Nighthawk X4S R7800

Бренды по названию

Популярные бренды