background image

Automatic address learning function to build the packet-forwarding information
table. The table contains up to 32K Media Access Control (MAC) addresses.

Store-and-forward transmission to remove bad packets from the network.

Active flow control to minimize packet loss and frame drops.

Half-duplex backpressure control.

Per-port status LEDs and system status LEDs.

NETGEAR green power-saving features:

-

Energy efficiency mode that fully conforms to the IEEE802.3az standard

-

Per-port automatic change to a lower power mode when the port link is down

Safety instructions and warnings

Use the following safety guidelines to ensure your own personal safety and to help
protect your system from potential damage.

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,
observe the following precautions:

This product is designed for indoor use only in a temperature-controlled and
humidity-controlled environment. Note the following:

-

For more information about the environment in which this product must operate,
see the environmental specifications in the appendix or the data sheet.

-

If you want to connect the product to a device located outdoors, the outdoor
device must be properly grounded and surge protected, and you must install an
Ethernet surge protector inline between the indoor product and the outdoor
device. Failure to do so can damage the product.

-

Before connecting the product to outdoor cables or devices, see
https://kb.netgear.com/000057103 for additional safety and warranty information.

Failure to follow these guidelines can result in damage to your NETGEAR product,
which might not be covered by NETGEAR’s warranty, to the extent permissible by
applicable law.

Observe and follow service markings:

-

Do not service any product except as explained in your product documentation.
Some devices should never be opened.

-

If applicable to your product, opening or removing covers that are marked with
the triangular symbol with a lightning bolt can expose you to electrical shock.

Hardware Installation Guide

8

Introduction

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

Содержание MS510TXM







































Отзывы: