NETGEAR MS108EUP Скачать руководство пользователя страница 2

Support and Community
Visit netgear.com/support to get your questions answered and access the latest
downloads.

You can also check out our NETGEAR Community for helpful advice at
community.netgear.com.

Regulatory and Legal
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français
canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian French at
https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity, visit
https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at
https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the
device to your place of purchase within your return period.

Do not use this device outdoors. The PoE port is intended for intra building connection
only.

Applicable to 6 GHz devices only: Only use the device indoors. The operation of 6 GHz
devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that
operation of this device is permitted in large aircraft while flying above 10,000 feet.
Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or
communications with unmanned aircraft systems.

This switch is designed for indoor use only. If you want to connect to a device located
outdoors, the outdoor device must be properly grounded and surge protected, and
you must install an Ethernet surge protector inline between the switch and the outdoor
device. Failure to do so can damage the switch.

WARNING:

Before connecting this switch to outdoor cables or devices, see

https://kb.netgear.com/000057103 for safety and warranty information.

Trademarks
© NETGEAR, Inc., NETGEAR, and the NETGEAR Logo are trademarks of NETGEAR, Inc.
Any non-NETGEAR trademarks are used for reference purposes only.

2

8-port Ultra60 PoE++ Multi-Gigabit (2.5G) Ethernet Plus Switch MS108EUP

Содержание MS108EUP































Отзывы: