NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTERNATIONAL LTD
Floor 1, Building 3,
University Technology Centre
Curraheen Road, Cork,
T12EF21, Ireland
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
Support and Community
Visit
to get your questions answered and access the latest
downloads.
You can also check out our NETGEAR Community for helpful advice at
Regulatory and Legal
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en
français canadien à
https://www.netgear.com/support/download/
.
(
If this product is sold in Canada, you can access this document in Canadian
French at
https://www.netgear.com/support/download/
.)
For regulatory compliance information including the EU Declaration of
Conformity, visit
https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
For NETGEAR’s Privacy Policy, visit
https://www.netgear.com/about/privacy-policy
.
By using this device, you are agreeing to NETGEAR’s Terms and Conditions at
https://www.netgear.com/about/terms-and-conditions
If you do not agree, return
the device to your place of purchase within your return period.
Do not use this device outdoors. The PoE source is intended for intra building
connection
only.
PoE considerations
The PoE and PoE+ power supplied by the switch is prioritized in ascending port
order (from port 1 to port 4), with a total power budget of 63W for the GS305Pv2,
and 83W for the GS305PP switch. If the power requirements for the attached
powered devices (PDs) exceed the total power budget of the switch, the PD
on the highest-numbered port is disabled to make sure that the PDs that are
connected to the higher-priority, lower-numbered ports are supported first.
PoE troubleshooting
Here are some tips for correcting PoE problems that might occur:
• If the PoE Max LED is yellow, disconnect one or more PoE devices to prevent
PoE oversubscription. Start by disconnecting the device from the highest-
numbered port.
• For each powered device (PD) that is connected to the switch, the associated
right port LED on the switch lights solid green. If the right port LED lights
yellow, a PoE fault occurred because of one of the conditions listed in the
following table.
PoE Fault Condition
Possible Solution
A PoE-related short circuit occurred on the port.
The problem is most likely with
the attached PD. Check the
condition of the PD or restart
the PD by disconnecting and
reconnecting the PD.
The PoE power demand of the PD exceeded
the maximum level that the switch permits. The
maximum level is 15.4W for a PoE connection or
30W for a PoE+ connection
The PoE current on the port exceeded the
classification limit of the PD.
The PoE voltage of the port is outside the range
that the switch permits
Restart the switch to see if the
condition resolves itself.
Mount the switch on a wall
We recommend that you use the wall-mount screws that came with the switch.
1. Locate the two mounting holes on the bottom panel of the switch.
2. Mark and drill two mounting holes in the wall.
3. The two mounting holes must be 1.53 in. (38.9 mm) apart, center-to-center.
Insert the supplied anchors into the wall and tighten the screws with a No. 2
Phillips screwdriver.
Leave about 0.125 in. (4 mm) of each screw protruding from the wall so that
you can insert the screws into the holes on the bottom panel.
Note:
The screws are 4.2 mm in diameter, 25 mm in length.
Specifications
October 2021
Specification
Description
Network interface
RJ-45 connector for 1000BASE-T, 100BASE-TX, or 10BASE-T
Network cable
Category 5 (Cat 5) or higher rated Ethernet cable
Ports
5 total. Ports 1-4 can provide PoE+; Port 5 is an uplink port.
Power adapter
Model GS305Pv2: 54V @ 1.25 A DC input
Model GS305PP: 54V @ 1.66 A DC input
Power consumption
Model GS305Pv2: 67.5W maximum; 1.4W standby
Model GS305PP: 88.89W maximum; 1.55W standby
PoE power budget
Model GS305Pv2: 30W maximum per PoE+ port with a total
PoE power budget of 63W for the switch
Model GS305PP: 30W maximum per PoE+ port with a total
PoE power budget of 83W for the switch
Dimensions (W x D x H)
6.2 x 4.0 x 1.1 in. (158 x 101 x 29 mm)
Weight
0.90 lb (0.41 kg)
Operating temperature
32–104°F (0–40°C)
Operating humidity
10%–90% relative humidity, noncondensing
