April 2008
This symbol was placed in accordance with the European Union Directive
2002/96 on the Waste Electrical and Electronic Equipment (the WEEE
Directive). If disposed of within the European Union, this product should be
treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
© 2008 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered
trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of their respective holders. Information is subject to
change without notice.
Horizontal Plane Radiation Pattern (X-Y) Azimuth
NETGEAR 5 dBi Omni-directional Antenna ANT2405 Specifications
Frequency range
2450 +/- 50MHz
Type
Dipole
Impedance
50 +/–5 Ohmns
Maximum input power
20W (without N/SMA adapter)
SWR
2.0 maximum
Return loss
–10 dB
Gain
5 dBi
Radiation
Omni-Directional
Polarization
Vertical
Beam degree
Horizontal 120°, Vertical 110°
Connector type
SMA female reverse
Material
TPE; PC; PBT
Color
White
Mounting base
Steel
Operating temperature
–10 to 60° C (14 to 140° F)
Storage temperature
–10 to 70° C (14 to 158° F)
Device size (l x w x h)
80 x 50 x 202 mm (3.14 x 1.96 x 7.95 in)
Weight
107.9 g (0.237 lb)
Warranty
2 years
5
0
-5
-10
-15
-10
-5
0
5
Vertical Plane Radiation Pattern (X-Z Elevation)
Radiation Pattern
Technical Support
Thank you for selecting NETGEAR products.
After completing the Smart Wizard configuration assistant, locate the serial number on the
bottom label of your product, and use it to register your product at
http://www.NETGEAR.com/register
.
Registration on the website or over the phone is required before you can use our telephone
support service. The phone numbers for worldwide regional customer support centers are
on the Warranty and Support Information card that came with your product.
Go to
http://kbserver.netgear.com
for product updates and Web support
.
5
0
-5
-10
-15
-10
-5
0
5
5
0
-5
-10
-15
-10
-5
0
5
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR
reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the
product(s) or circuit layout(s) described herein.
Federal Communications commission (FCC) Compliance Notice: Radio Frequency
Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
To comply with FCC regulations, the ANT2405 should only be used with devices that have been
FCC approved for use with the NETGEAR ANT2405. Check the NETGEAR website at http://
tools.netgear.com/legal/fcc_antennas.html for an updated list of FCC approved devices.
Note:
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna; (2) Increase the separation
between the equipment and receiver; (3) Connect the equipment to an outlet or circuit different from
that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician
for help.
FCC and EU Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antenna must be less than 20 cm (8 inches) during normal operation.
This device should not be co-located with other transmitters.
For EU, use of any antenna requires careful planning and extra considerations to comply with EU
emissions and health standards and regulations. Antenna installation must comply with the
maximum level authorized by each country.
