Netbiter EasyConnect EC310
Netbiter EasyConnect EC350
Installa
Ɵ
on Guide
SP1829, Rev. 1.40, July 2015
compatible
Field wiring terminals shall be connected with minimum wire size 24 AWG
Use the IPcon
fi
g tool to set up a sta
Ɵ
c IP address, gateway or DNS server for the
WAN port on the Netbiter EasyConnect.
About the IPcon
fi
g U
Ɵ
lity
The Windows-based IPcon
fi
g u
Ɵ
lity is used for making TCP/IP network se
ƫ
ngs
in the Netbiter. The u
Ɵ
lity scans the Ethernet network for connected Netbiter
devices and allows the user to set the IP address, net mask, gateway, DNS and
hostname for each unit.
Installa
Ɵ
on Procedure
Download and run the self-extrac
Ɵ
ng installa
Ɵ
on package
IPcon
fi
g
from
h
Ʃ
p://www.netbiter.com/support
Scanning for connected devices
Ensure that the Netbiter units to be installed are connected on the same
Ethernet network as the PC running IPcon
fi
g. Use standard Ethernet cables,
straight-through or crossover.
When IPcon
fi
g is started it will scan the Ethernet network for Netbiter devices. All
detected devices will be presented
in a list in the main window. To start
a new scan for devices, click the
Scan
bu
Ʃ
on.
Changing IP se
ƫ
ngs
To change the IP se
ƫ
ngs for a
detected device, double-click the
device in the list. This opens a
dialog from which the required IP
con
fi
gura
Ɵ
on can be made.
The default password for
authen
Ɵ
ca
Ɵ
on of the new se
ƫ
ngs is the
Ac
Ɵ
va
Ɵ
on Code
. Clicking
Set
will cause
the Netbiter device to reboot, a
Ō
er which the new se
ƫ
ngs will be enabled.
Before communica
Ɵ
ng with Netbiter Argos, the Netbiter EasyConnect must be
ac
Ɵ
vated. This requires the
System ID
and
Ac
Ɵ
va
Ɵ
on Code
, both of which are
provided on a printed sheet together with the Netbiter.
To open a new account on Netbiter Argos:
1.
Go www.netbiter.net and click on the
Create an account
link.
2.
Follow the instruc
Ɵ
ons and log in to the new account.
3.
Select the primary use for the unit and click on the
Ac
Ɵ
vate
bu
Ʃ
on.
To use an exis
Ɵ
ng Netbiter Argos account:
1.
Go to www.netbiter.net and log in to your account.
2.
Go to the menu
Management >> All Systems >> Add system
See the online help if required.
Requirements for Mobile Communica
Ɵ
on
The informa
Ɵ
on listed below should be entered at Netbiter Argos, at the
Mobile
Network
con
fi
gura
Ɵ
on page, under the management tab for the system.
•
The phone number for the SIM card.
•
For a SIM card supplied by another operator, the access point name (APN)
for the SIM card is also required. Enter the username and password if
required by the operator.
The phone number and APN informa
Ɵ
on should be supplied with the SIM card. If
not, please contact the operator for the correct informa
Ɵ
on.
Note that for a SIM card from another operator, the PIN code must be disabled.
Online Help
The online help is accessed by clicking on
the icon in the upper right corner, as shown
here.
Order Code
EC310: NB1007
EC350: NB1005
EC350 (no antenna): NB1008
Mobile communica
Ɵ
on (EC350 only)
5-band 3G/UMTS (WCDMA/FDD):
800/850, 900, 1900, 2100 MHz
Quad-band GSM/GPRS: 850, 900, 1800,
1900 MHz
1
Relay Output
2
Digital Inputs
(dry contact type)
4 Analog Inputs
All 4 with support for V, mA
2 with support for Pt100
Serial Port #1
RS-232 (Tx, Rx, GND)
Serial Port #2
RS-485
Antenna Connector Mobile (EC350 only)
SMA female
Antenna Connector GPS (EC350 only)
SMA female (ac
Ɵ
ve or passive antenna)
USB Interface
Micro USB, USB 2.0
Protocols
Modbus RTU
Moun
Ɵ
ng
DIN rail (EN 50022)
Wall moun
Ɵ
ng
Dimensions (H x W x D)
25.6 x 135 x 92 mm
Temperature
Opera
Ɵ
ng: -40 °C to +65 °C
Storage: -45 °C to +85 °C
Humidity range
5-95 % RH, non-condensing
Power Supply
12-48 VDC, 6 W, LPS
Power Consump
Ɵ
on, typical
EC310:
2.5 W
EC350:
4.5 W
Cer
Ɵ
fi
ca
Ɵ
ons
EC310:
CE, ROHS,
C
UL
US
EC350:
CE, ROHS, Telec
JATE,
C
UL
US,
FCC, IC, PTCRB, RCM
Cer
Ɵ
fi
ca
Ɵ
ons Pending
EC310
: ATEX/Haz.Loc
EC350:
ATEX/Haz.Loc
Technical Speci
fi
ca
Ɵ
ons
HMS Industrial Networks AB
Box 4126
300 04 Halmstad
Sweden
Phone
+46 (0)35 - 17 29 00
Fax
+46 (0)35 - 17 29 09
Web
www.hms.se
Support
+46 (0)35 - 17 29 20
Web
www.netbiter.com/support
Save time, save energy, save resources!
©2014 HMS Industrial Networks - All rights reserved - HMS reserves the right to make modi
fi
ca
Ɵ
ons without prior no
Ɵ
ce.
For a Netbiter SIM card, the APN se
ƫ
ngs are pre-con
fi
gured on
Netbiter Argos and the PIN code is disabled upon delivery.
Connectors and I/O’s - Top
Power connector
SIM card slot
*
I/O Terminal
block
(see table)
NOTE: The new se
ƫ
ngs can be tested by opening a web browser
and entering the IP address as con
fi
gured above. To discover the
device’s IP address when using DHCP - start a new scan with the IP
Con
fi
g u
Ɵ
lity to view the new network con
fi
gura
Ɵ
on informa
Ɵ
on.
Connectors - Bo
Ʃ
om
RS-232
RS-485
GPS antenna
connector
*
WAN
Pin
Description
Rx
Rx Recieve Input RS-232
Tx
Tx Transmit Output RS-232
GND
Signal ground
3-pin RS-232 Connector
Pin
Description
A
RS-485 Line A (+)
B
RS-485 Line B (-)
COM
ISO GND (Isolated ground)
3-pin RS-485 Connector
D
E
Manual WAN Con
fi
gura
Ɵ
on
C
Micro USB
connector
Protec
Ɵ
ve Earth
(for Ethernet ports)
Pin Label
Description
1
(Relay) NO
Relay Output, NO, Isolated
2
(Relay) COM
Relay Output, COM, Isolated
3
(DI/Pulse In) DI1+
Digital input 1 current source
4
(DI/Pulse In) DI1-
Digital input 1
5
(DI/Pulse In) DI2+
Digital input 2 current source
6
(DI/Pulse In) DI2-
Digital input 2
7
(Analog In) AI1
Analog Input 1
8
(Analog In) AI2
Analog Input 2
9
(Analog In) AI3
Analog Input 3
10
(Analog In) AI4
Analog Input 4
11
(Analog In) COM
Analog Ground
Connec
Ɵ
ons on I/O Terminal Block
IMPORTANT! Do not select the DHCP op
Ɵ
on if there is no DHCP
server available on the network.
Package Contents
Item
Descrip
Ɵ
on
NB1005 or
NB1008 or
NB1007
EC350
EC350 (no antenna)
EC310
Connectors
Screw connectors for I/O, RS-232 and RS-485 teminals
System ID/Ac
Ɵ
va
Ɵ
on code
Printed document with ID and code required to install product
Installa
Ɵ
on Guide
This document
Stub antenna (NB1005 only)
Female SMA connector
Ac
Ɵ
vate the Netbiter EasyConnect
B
11
1
LAN
2G/3G antenna
connector
*
*
Netbiter EC350 only
•
Do not connect power to digital inputs!
•
Relay max 24V AC/DC, 1A
Once the Netbiter is online at Netbiter Argos, please check
that the unit is running the latest
fi
rmware.
Mode bu
Ʃ
on
*
Ethernet link indicators
