•
AltaVault Resources:
https://mysupport.netapp.com/info/web/ECMLP2606636.html
•
AltaVault library:
http://mysupport.netapp.com/documentation/productlibrary/index.html?productID=62032
•
Hardware Universe:
https://hwu.netapp.com
•
More infomation:
http://www.netapp.com
HELPFUL LINKS
Visit the NetApp web site for more information.
NetApp Support Sit
e
CAUTION
PRUDENCE
CAUTION
PRUDEN
CE
AT
TENTIO
N
IN
SE
R
T
PSU
BLA
N
K
IN
SLO
TS
2
O
R
3
CAUT
ION
PRUDENC
E
CAUTION
PRUDENCE
A
TTENT
ION
INS
ER
T
PSU
BL
ANK
IN
S
LO
TS
2
O
R
3
4
2
3
1
4
2
3
1
4
2
3
1
4
2
3
1
LNK
LNK
IOM6
IO
M6
LNK
LNK
IOM6
IO
M6
CAUTION
PRUDEN
CE
AT
TENTIO
N
IN
SE
R
T
PSU
BLA
N
K
IN
SL
O
TS
2
O
R
3
CAUT
ION
PRUDENCE
CAUTION
PRUDENCE
4
2
3
1
4
2
3
1
LNK
LNK
IOM6
IO
M6
Power switch
Open a connection to the serial console port using a terminal program such as PuTTY, and log in using the
default login (admin) and default password (password). You can now complete the AltaVault deployment as described
in the NetApp AltaVault Cloud Integrated Storage Administration Guide.
You must power on all the disk shelves before powering on the controller. Powering on
the controller before the disk shelf prevents AltaVault OS from operating normally.
Power switch
7
8
9
10
e0b
e0a
0
e0e
e0f
e0c
e0d
LINK LINK
LINK
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
4.0TB
Digital Display
(two digits)
Shelf fault LED
Shelf ID button
Left ear
cover
Power on the disk shelf; move the power switch to the ON ( | ) position.
BOTH power supplies MUST be powered on.
• Verify that the power supplies are working correctly:
PSU OK LED ( ) is lit green in each power supply.
• View the disk shelf LEDs (on shelf front) to verify the disk shelf powered on correctly:
Power LED ( ) is lit green.
Fault LED ( ) is not lit.
Visually verify that the ID for each disk shelf is unique, and if not, set the disk shelf ID.
NOTE: Valid shelf IDs: shelf 1 ID 00; shelf 2 ID 10, shelf 3 ID 01, shelf 4 ID 11.
ID 00 is the default shelf ID.
a. Using one hand, hold the left ear cover between your thumb and index finger.
Pull either the top or the bottom of the cover until one end is released.
Pull off the left ear cover.
b. Press and hold the shelf ID button until the first digit on the digital display blinks.
c. Press the button until the desired number (between 0 and 9) is displayed.
This number continues to blink.
d. Repeat steps b and c for the second digit.
e. Press and hold the button until the second number stops blinking.
Both numbers on the digital display should blink and the shelf fault
LED illuminates in about five seconds.
The fault LED stays lit until you power-cycle the shelf.
f. Power-cycle the disk shelf to make the new disk shelf ID takes effect.
g. Replace the left ear cover.
Power on the controller; move the power switch to the ON (|) position.
BOTH power supplies MUST be powered on.
• Verify that the power supplies are working correctly:
PSU OK LED ( ) is lit green in each power supply.
• View the system LEDs (on controller front) to verify the controller powered on correctly:
Power LED ( ) is lit green.
System attention LED ( ) blinks for a few minutes while AltaVault OS is booting up.
The System attention LED turns off when AltaVault OS is finished booting up.
Install the bezel
• Hold the bezel parallel to the front of the controller.
• Install the bezel on the controller front as shown in the illustration.
• The bezel will snap into place.
Complete system setup
|
5
Install hardware
Install disk shelves
Connect cables
Complete system setup
2
Prepare for installation
1
3
4
5
AltaVault System
Installation and Setup Instructions
Prepare for installation
|
1
You provide
In the box
RJ45 serial adapter
SAS cables
Power cables
2 per controller chassis
2 per disk shelf
1
Power on the disk shelf
2
Power on the controller
3
Finish the AltaVault setup over the serial console
1.
2.
1.
2.
Computer & LAN access
Initial configuration is done via serial console
(for example PuTTY)
Additional network cables
For connecting your storage system to Ethernet switches
Rack space - 10U
AltaVault system chassis: 6U
AVA10S disk shelf: 4U
Serial cable connection
Fiber cables
mini SAS HD-QSFP cable
(controller to shelf)
QSFP-QSFP cable
(shelf to shelf)
Screwdriver and screws
For securing hardware into racks
