NetApp AFF A300 Скачать руководство пользователя страница 15

Страница: 15 / 18

If the system-level diagnostics
tests…

Then…

Were completed without any
failures

a. Clear the status logs:

sldiag device clearstatus

b. Verify that the log was cleared:

sldiag device status

The following default response is displayed:

SLDIAG: No log messages are present.

c. Exit Maintenance mode on both controllers:

halt

The system displays the LOADER prompt.

You must exit Maintenance mode on both
controllers before proceeding any further.

d. Enter the following command on both controllers at the LOADER

prompt:

bye

e. Return the controller to normal operation:

If your system is running
ONTAP…

Then…

With two nodes in the cluster

Issue these commands:

node::> cluster ha modify

-configured true``node::> storage failover modify
-node node0 -enabled true

With more than two nodes in the
cluster

Issue this command:

node::> storage failover modify

-node node0 -enabled true

In a two-node MetroCluster
configuration

Proceed to the next step. The MetroCluster switchback procedure is
done in the next task in the replacement process.

In a stand-alone configuration

You have no further steps in this particular task. You have completed
system-level diagnostics.

Содержание AFF A300



















Результаты поиска

Содержание AFF A300

Отзывы:

Похожие инструкции для AFF A300

Бренды по названию

Популярные бренды

NetApp AFF A300, Руководство пользователя

Результаты поиска

Содержание AFF A300

Отзывы:

Похожие инструкции для AFF A300

Бренды по названию

Популярные бренды