NetApp AAF A700 Скачать руководство пользователя

Страница: 16 / 19

failures resulting from testing the component.

7. Proceed based on the result of the preceding step.

If the system-level diagnostics
tests…

Then…

Were completed without any
failures

a. Clear the status logs:

sldiag device clearstatus

b. Verify that the log was cleared:

sldiag device status

The following default response is displayed:

SLDIAG: No log messages are present.

c. Exit Maintenance mode on both controllers:

halt

The system displays the LOADER prompt.

You must exit Maintenance mode on both
controllers before proceeding any further.

d. Enter the following command on both controllers at the LOADER

prompt:

bye

e. Return the node to normal operation:

With two nodes in the cluster

Issue these commands:

node::> cluster ha modify

-configured true

node::> storage failover modify -node node0
-enabled true

With more than two nodes in the
cluster

Issue this command:

node::> storage failover modify

-node node0 -enabled true

In a two-node MetroCluster
configuration

Proceed to the next step.

The MetroCluster switchback procedure is done in the next task in the
replacement process.

In a stand-alone configuration

You have no further steps in this particular task.

You have completed system-level diagnostics.

Содержание AAF A700




















Результаты поиска

Содержание AAF A700

Отзывы:

Похожие инструкции для AAF A700

Бренды по названию

Популярные бренды

NetApp AAF A700, Руководство пользователя

Результаты поиска

Содержание AAF A700

Отзывы:

Похожие инструкции для AAF A700

Бренды по названию

Популярные бренды