background image

WARRANTY

NESLAB Instruments, Inc. warrants for 12 months from date of shipment any NESLAB unit according to the

following terms.

Any part of the unit manufactured or supplied by NESLAB and found in the reasonable judgment of NESLAB

to be defective in material or workmanship will be repaired at an authorized NESLAB Repair Depot without

charge for parts or labor. The unit, including any defective part must be returned to an authorized NESLAB

Repair Depot within the warranty period. The expense of returning the unit to the authorized NESLAB Repair

Depot for warranty service will be paid for by the buyer. NESLAB’s responsibility in respect to warranty claims

is limited to performing the required repairs or replacements, and no claim of breach of warranty shall be

cause for cancellation or recision of the contract of sales of any unit.With respect to units that qualify for field

service repairs, NESLAB’s responsibility is limited to the component parts necessary for the repair and the

labor that is required on site to perform the repair. Any travel labor or mileage charges are the financial respon-

sibility of the buyer.

The buyer shall be responsible for any evaluation or warranty service call (including labor charges) if  no

defects are found with the NESLAB product.

This warranty does not cover any unit that has been subject to misuse, neglect, or accident. This warranty

does not apply to any damage to the unit that is the result of improper installation or maintenance, or to any

unit that has been operated or maintained in any way contrary to the operating or maintenance instructions

specified in NESLAB’s Instruction and Operation Manual. This warranty does not cover any unit that has been

altered or modified so as to change its intended use.

In addition, this warranty does not extend to repairs made by the use of parts, accessories, or fluids which are

either incompatible with the unit or adversely affect its operation, performance, or durability.

NESLAB reserves the right to change or improve the design of any unit without assuming any obligation to

modify any unit previously manufactured.

THE FOREGOING EXPRESS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE.

NESLAB’S OBLIGATION UNDER THIS WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO THE

REPAIR OR REPLACEMENT OF DEFECTIVE COMPONENT PARTS AND NESLAB DOES NOT ASSUME

OR AUTHORIZE ANYONE TO ASSUME FOR IT ANY OTHER OBLIGATION.

NESLAB ASSUMES NO RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES

INCLUDING, BUT NOT LIMITED TO LOSS OR DAMAGE TO PROPERTY, LOSS OF PROFITS OR REV-

ENUE, LOSS OF THE UNIT, LOSS OF TIME, OR INCONVENIENCE.

This warranty applies to units sold in the United States. Any units sold elsewhere are warranted by the affiliated

marketing company of NESLAB Instruments, Inc. This warranty and all matters arising pursuant to it shall be

governed by the law of the State of New Hampshire, United States. All legal actions brought in relation hereto

shall be filed in the appropriate state or federal courts in New Hampshire, unless waived by NESLAB.

Содержание RTE-111




























Отзывы: