Neptune Technology E-Coder)R900i Скачать руководство пользователя страница 45

Страница: 45 / 52

E-Coder)R900

Installation and Maintenance Guide

Glossary

antenna (whip)

The RF antenna that can be removed to upgrade to a through-the-lid
antenna.

antenna (pit)

The MIU antenna used for pit installations.

conical-shaped gasket

The cone-shaped rubber gasket on antenna cable used to seal cable
at top of connector housing.

connector housing

The black plastic 1/4-turn connector used to waterproof antenna
cable connection to pit MIU.

connector nut

The black plastic nut used to depress conical-shaped gasket and seal
antenna cable at the top of connector housing.

flat washer

The washer used to seal cable connector housing to pit MIU.

light sensor

The component located under the recess that is used to activate the
LCD. See Liquid Crystal Display.

Liquid Crystal Display (LCD)

The component where the meter reading and value-added icons are
displayed.

MIU

Meter Interface Unit.

register read time

The default time is once an hour for ProRead™ and 15 minute inter-
val for E-Coder (ARB VII). Custom time is not available.

serial number

A unique identification number given to each MIU at the factory. The
default value is the last programmed plus one. Custom serial num-
bers are not available.

tamper nail

The small black plastic nail used to secure the battery pack to the
Inside enclosure.

transmission time

The time between MIU transmissions. The default is approximately
fourteen (14) seconds. Custom time is not available.

Содержание E-Coder)R900i





















































Результаты поиска

Содержание E-Coder)R900i

Отзывы:

Похожие инструкции для E-Coder)R900i

Бренды по названию

Популярные бренды

Neptune Technology E-Coder)R900i, Руководство по установке и обслуживанию

Результаты поиска

Содержание E-Coder)R900i

Отзывы:

Похожие инструкции для E-Coder)R900i

Бренды по названию

Популярные бренды