Neoway N3830 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 27

Neoway N3830 Скачать руководство пользователя страница 27

N3830 Router

Operation Guide

Copyright © Neoway Technology Co., Ltd

26

8 LED Indicators

Led indicators on the device, from top down, left to right are PWR, SYS, SIG, 485, LAN, and DAT.

Table 8-1 LED Indicators

Name Function description

Remarks

PWR

Power indicator, steady
green when the power
is turned on

The PWR indicator indicates whether the device is powered on.

SYS

System

indicator,

blinking green

After the transparent transmission function is enabled and the
device is connected to the server, this indicator starts to blink once
every second. If the device fails to connect to the server, the SYS
indicator does not flash.

SIG

Signal indicator, blinking
green

When the signal CSQ value is greater than or equal to 15, the
indicator blinks once per second.

When the value is lower than 15, the indicator flashes 4 times per
second.

485

485

port

indicator,

blinking green

When data is input from an external source into the device via the
485 port, this indicator flashes 4 times per second.

When data is output from the device to an external destination, this
indicator does not flash.

LAN

Reserved

Reserved

DAT

Data indicator, blinking
green

After the transparent transmission is enabled, the indicator flashes
4 times per second when receiving data from the server. It does
not flash when sending data.

«
...
25
26
27

Содержание N3830




























Отзывы:

Нет отзывов