background image

Notices 

Notices 

Copyright 

All rights reserved. This publication may not be reproduced, transmitted, 

transcribed, stored in a retrieval system, or translated into any language or 

computer language, in any form or by any means, electronic, mechanical, 

magnetic, optical, chemical, manual or otherwise, without the prior written 

consent of Neousys Technology, Inc. 

Disclaimer 

This manual is intended to be used as an informative guide only and is subject 

to change without prior notice. It does not represent commitment from Neousys 

Technology Inc. Neousys Technology Inc. shall not be liable for any  direct, 

indirect, special, incidental, or consequential damages arising from  the use of 

the product or documentation, nor for any infringement on third party rights. 

Patents and 

Trademarks 

Neousys, the Neousys logo, Expansion Cassette, MezIO

TM

  are registered 

patents and trademarks of Neousys Technology, Inc. 

Windows is a registered trademark of Microsoft Corporation. 

Intel

®

, Core™ are registered trademarks of Intel Corporation 

NVIDIA

®

, GeForce

®

 are registered trademarks of NVIDIA Corporation 

All other names, brands, products or services  are trademarks or registered 

trademarks of their respective owners. 

FCC 

Conformity 

This equipment has been tested and found to comply with the limits for a Class A 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference when the equipment is 

operated in a commercial environment. This equipment generates, uses, and can 

radiate radio frequency energy and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful 

interference in which case the user will be required to correct the interference at his 

own expense.

 

CE Conformity 

The product(s) described in this manual complies with all applicable European 

Union (CE) directives if it has a CE marking. For computer systems to remain CE 

compliant, only CE-compliant parts may be used. Maintaining CE compliance also 

requires proper cable and cabling techniques. 

 

Содержание PCIe-PoE334LP








































Отзывы: