NeoDen K1830 Скачать руководство пользователя страница 8

Страница: 8 / 52

1.4 Important Notice

Figure 6-The air supply of the equipment shall not be less than0.6MP

Figure 7- Feeder Pressure 0.55MP

Warning of failure risk of camera identification

，

please referring to Figure 3 and

Figure 5

：

The following parts are forbidden to touch and impact



Front IC Camera



Back IC camera



Left mark camera



Right mark camera



Left mark camera light source



Right mark camera light source

Warning of accuracy failure risk, refer to Figure 3: The following components are
prohibited from touching and impacting.



Return to zero column

For the risk of accuracy failure, refer to Figure4: When manually moving XY, it must
be carried out on the X-axis beam moving point;

Warning of electric shock, be sure to follow the requirements below

：



Connect the input power supply that meets the requirements of the equipment, the

electrical interface of the machine to the ground must be effectively grounded

；



Any time you enter the case and stick to the head for maintenance, you need to shut down

the machine properly and cut off the power supply;

Warning of equipment life reduction

，

be sure to follow the requirements below

：



When installing the equipment, the equipment must be leveled

；



Correct shutdown: shut down the operating software and the system before turning off

the main power switch

；

Zhejiang

NeoDen Technology Co.,Ltd.

Содержание K1830





















































Результаты поиска

Содержание K1830

Отзывы:

Похожие инструкции для K1830

Бренды по названию

Популярные бренды

NeoDen K1830, Руководство пользователя

Результаты поиска

Содержание K1830

Отзывы:

Похожие инструкции для K1830

Бренды по названию

Популярные бренды