ProLink kit
contents
Installation
NEO interface for iPod
Installation Guide/User Manual
user manual
See back for more
1
3
4
5
6
7
8
9
NEO logo is a trademark of NEO Car Audio, Inc. SiriusConnect, Sirius and XM logos are trademark of SiriusXM. The Made for iPod logo is a trademark of Apple Inc. Apple iPod is not included in the package. For our detailed
terms and conditions please visit our website at www.neocaraudio.com.
ProLink-AVW rev 091311
for selected Audi/VW vehicles
Installation Guide/User manual
NBM12345678
XXX- XXX-XXX
Module serial number
Product part number
Identifying your ProLink kit
P2AUDV1, P2AVWV1, P2AVWTV1 -
These
kits work in CDC Emulation mode.
ProLink module
iPod docking
cable
P2AVWV1
R1 connector
P2AUDV1
connector
P2AVWV1
R2 connector
P2AVWTV1
connector
Connection Diagram
*Do not connect the iPod dock cable under any circumstance to the SIRIUS module connector!
Improper connection can cause permanent damage to iPod/SIRIUS module.
IR receiver
(optional)
ProLink module
(front)
ProLink module
(back)
Update port
(USB to PC)
iPod dock cable*
iPod/iPhone
(not included)
Vehicle BUS
connector
SIRIUS SAT radio
(not included)
Note: works with
P2AVWSV1 only!
Auxiliary device
(not included)
AUX connector
(optional)
SIRIUS connector*
Vehicle BUS Connector - P2AUDV1 Connector
To factory harness
in vehicle
P2AUDV1 Connector
To ProLink
Interface Module
To ground
You can access the CD changer connector located on the back of the radio. Unplug the factory connection
if present and plug the P2AUDV1 connector into the receptacle. The connector should securely lock.
Ground wire MUST be connected to a stable grounding point.
Vehicle BUS Connector - P2AVWV1 R1 Connector
You can acces the CD changer connector located on the back of the radio. Unplug the factory connection if
present and plug the P2AVWV1 R1 connector into the receptacle. The connector should securely lock.
Ground wire MUST be connected to a stable grounding point.
P2AVWV1 R1 connector
Vehicle BUS Connector - P2AVWV1 R2 Connector
To ProLink
Interface Module
12 to 16 pin adapter
You can access the CD changer connector located on the back of the radio. Unplug the factory connection if
present and plug the P2AVWV1 R2 connector into the receptacle. The connector should securely lock.
Ground wire MUST be connected to a stable grounding point.
P2AVWV1 R2 connector
1. Verify compatibility
5. Route kit to glove box or other accessible location
6. Connect battery & test
7. Complete install by re-installing radio
2. Disconnect battery
3. Remove radio from car
4. Install ProLink cable
Some radios will enter an anti-theft security mode and will lock requiring the radio’s security code
to be entered to unlock it. This code can be requested from the vehicle’s dealership.
Only one of these cables will be included with your kit
12 to 16 pin adapter
To ProLink
Interface Module
12 to 16 pin adapter
12 to 16 pin
adapter
P2AUDV1, P2AVWV1, P2AVWTV1
P2AVWV1 - R2 Connector Modification
iPod:
Toggle the auido sources between iPod
and SIRIUS/AUX
iPod:
Skip to the next ALBUM
* ARTIST is currently not supported
iPod:
Skip to the previous ALBUM
Play / Pause
iPod:
Repeat one / Repeat all / Repeat
off
iPod:
Next Track
iPod:
Previous Track
iPod:
Skip to the next PLAYLIST
iPod:
Skip to the previous PLAYLIST
SOURCE
3
1
4
6
Optional Remote Kit: Functions for iPod
below is required.
NOTE:
Disconnect main radio
harness and locate SAT
connector. Remove it
from main harness by
pressing on the release
tab of the SAT connector.
Slide out the inner part of
the SAT connecor from
plastic housing.
Disassemble the ProLink
P2AVWV1 R2 connector the
same way as the factory
SAT connector.
Remove the SAT wires from
the factory connector by
releasing the pins with a small
screw driver or ball point pen.
Put plastic connector covers
back on. Insert the
P2AVWV1 R2 connector to
factory VW main harness.
Connect ground wire to
chassis of radio.
Relocate wires to
P 2 A V W V 1 R2 connector keeping
the same order and location.
2
3
4
5
6
7
SAT
Connector
pins 1,3, 7
pins 1,3, 7
P2AVWV1
R2 connector
some
