from 1 speaker
Audio is not coming from
the speakers
to its wire size.
The 10-pin sound connector is not aligned
correctly
The audio cable is not inserted properly.
Make sure that 10-pin sound connector on
vehicle cable is aligned correctly
Make sure that the audio cable inserted
properly.
3.10 Support
For questions or technical support please visit
http://neocaraudio.com/support.html
Your question will be
answered by the first available representative.
Chapter 4. Warranty, license agreement and disclaimers
One Year Limited Warranty
The quality controls used in the manufacture of this product ensure your satisfaction. This warranty applies only to the original purchaser of this product
from an authorized dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspection by NEO CAR AUDIO authorized
personnel, is found to have failed in normal use due to defects in material or workmanship. This warranty does not apply to installation expenses. Operating
this unit under conditions other than those recommended or voltages other than the voltage indicated on the unit, or attempting to service or modify the unit,
will render this WARRANTY VOID. Unless otherwise proscribed by law, NEO CAR AUDIO shall not be liable for any personal injury, property damage
or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse, improper installation or
alteration of this product.
All parts of this NEO CAR AUDIO product are guaranteed for a period of 1 year as follows:
Within the first 12 months from date of purchase, subject to the conditions above, NEO CAR AUDIO will repair or replace the product if it is defective in
material or workmanship providing it is returned to NEO CAR AUDIO, with PROOF OF PURCHASE from an authorized dealer. If you have a problem
with this product, please call or write to our Customer Service Dept.
All warranty repairs must have a RMA number from our service department. Contact Neo Car Audio for further warranty repair info.
Warning:
1.
This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause
damage or malfunction.
2.
Do not disassemble or alter the cable and interface box.
3.
Make the connections correctly
4.
Do not cut away the wire sheath and use the power for other equipments.
5.
Do not install in locations which might hinder vehicle operation or create hazards for vehicle occupants.
6.
Have the wiring and installation done by professionals.
7.
Arrange wiring so it is not crimped or pinched.
8.
Do not use this product for purposes other than stated for the vehicle.
Caution:
1.
The ACC Switch Output Connector has 10mA drive capability only. You must use a relay if higher ACC power output is required.
2.
Use of headphones while operating an automobile or moving vehicle is not recommended and is unlawful in some countries and areas.
3.
Be careful and attentive on the road. Stop operation of the Neo Adapter if you find it disruptive or distracting while driving. The driver of a motor
vehicle should not operate the Neo Adapter while driving.
FCC Class B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encourages to try to correct the interference by one or more of the
following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/television technician for help.
Notice 1: The changes or modifications not expressly approved by the party responsible for compliance could void the user authority to operate the
equipment.
Notice 2: Shielded interface cables, if any, must be used in order to comply with the emission limits.
Copyrights, warnings, and other information
The illustrations, technical information, data and descriptions contained in this publication are subject to change without notice. This publication, together
with all information contained in it, and all intellectual property rights on this publication remain the property of NEO CAR AUDIO. The user may not
pass this publication on to third parties. No liability will be accepted for any inaccuracies or omissions in this publication, although due care has been
taken to make it as complete and accurate as possible
