Use if:
Radio has
TAPE/DISC
button OR has an external CD Changer OR RSE/DVD. EXT CDC & RSE/DVD will continue
to work in this mode (EX: Denali w/ lower Changer). Radio
MUST
have a BAND button.
See C if you have XM subscribed.
Radio Button Used To Access iPod:
Press the Band button and toggle to XM1 or XM2 – iPod will now be on these.
C) XM mode with SAT:
(XM radio
IS
being used/subscribed to)
Do Not Use if:
Radio does NOT have a BAND button.
Use if:
XM is subscribed
AND
Radio has
TAPE/DISC
OR
CD/AUX
button OR has an external CD Changer OR RSE/DVD.
EXT CDC & RSE/DVD will continue to work in this mode. Radio
MUST
have a BAND button.
Radio Button Used To Access iPod:
Press the Band button and toggle to XM1 – iPod will now be on XM1. XM2 stays XM.
IMPORTANT-IF USING SETTING C: Special Installation steps are needed. Please see Step 7.
iPod Dip Switch Position
Selected Mode
3
4
Radio Button
Used to Access
CD Changer OR
DVD disconnected
XM must be
subscribed to
A) CD Changer Mode
ON – DWN
ON – DWN
CD/AUX
YES
NO
B) XM Mode
(w/o SAT, NOT subscribed to)
OFF – UP
ON – DWN
BAND
NO
NO
C) XM Mode
(SAT IS being subscribed to)
OFF – UP
OFF – UP
BAND
NO
YES
INSTALLATION SUMMARY:
The PODGM12V2comes with three parts: 1) the vehicle cable, 2) the PODGM12V2 control module and 3) the iPod cable.
Simply remove the radio, plug in the vehicle cable, connect the module and then the iPod cable. Route the iPod cable to your
desired location. The iPod is accessed on the radio by pressing the CD or SAT button on the radio. If your not comfortable
doing it, have a professional handle it.
Do you have an XM tuner is the vehicle? We offer an optional add on cable – the CBLGMXM; that makes the install easier.
This cable allows you to connect this kit directly to the XM tuner instead of behind the radio. That means that in most cases,
radio removal isn't even necessary since the tuner is usually behind the glove box. If you are currently subscribing to XM, the
PODGM12V2 REQUIRES that you splice in to the XM data wire for it to work. If you purchase the optional CBLGMXM
cable you do NOT have to splice the wire.
INSTALLATION STEPS
(Professional Installation is
STRONGLY
Recommended)
Step 1:
Choose the correct dip switch settings above that meet your preferences and radio capabilities.
Step 2:
Eject
ALL
CD’s from CD-player or Changer.
Step 3:
Remove radio from dash.
Step 3:
Unplug the 24pin and 12pin connectors from the radio and plug them into the Neo vehicle cable
Step 4:
Plug the Neo’s 24pin and 12pin – GM-C cable into the port on the radio.
Step 5:
Using the cable with the round din plug and 12pin plug, connect it to the GM-C cable.
Step 6:
Plug the round din plug on the GM-C cable to the Neo ProLink where it is labeled “RADIO”.
(Do
Not
connect your ipod until the install is complete).
If you are using settings A or B, go directly to Step 8. For setting C, continue:
Step 7: Setting C – 3&4 are OFF.
Locate the DATA wire on the XM receiver. The DATA wire is connected to either pin 7
OR pin 15 of the connector for the XM receiver box.
(Only 1 wire will be present in 7 OR 15 not BOTH)
-
Cut this DATA wire approx 4 inches away from the receiver box.
-
Grab the end of the wire that is going to the back of the radio and securely tape it. This MUST be done to
prevent a bare wire from making contact with anything.
-
Connect the other end of the DATA line (receiver side) to the blue wire (included with this kit)
-
Connect the Data wire (blue) to the White Neo box where it is labeled “XM Receiver”.
-
IF after connecting, you get ipod & XM over the same channel, you A) didn’t connect it well enough or B) you
are connected to the ONSTAR box which looks very close to the XM tuner)
Step 8:
If using the AUX, connect the audio output of your auxiliary device to the AUX input jack on the Neo ProLink.
Step 9:
Plug the iPod cable to the Neo ProLink adapter box where it is labeled “iPod”.
Step 10:
Test to make sure everything is working before you reinstall the radio.
Step 11:
Reinstall the radio back into the dash of the vehicle. DO NOT PERMANENTLY HIDE BOX/MODULE BEHIND
RADIO. If possible, put in a place where its relatively easy to get to in the future. Customer should NOT have to return to
installer just to access box.
*For changes to the dip switches, see reset instructions above. DO NOT change settings with box plugged in.
Install Tip: Place Neo Box in a location you can access, in case you want to change dip switch modes later.
Location of XM Tuner
