Nemtek M18, Руководство пользователя

Страница: 2 / 2

Using your Merlin Keypad
2
Switch the fence On / Off
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
#
To switch the fence On or Off enter your four digit PIN followed by the # key. The keypad
will beep twice to confirm that the fence is off and three times when the fence is turned on.
"
If the red ON light is on or flashing then the fence is energized.
"
Don’t pause for more than 5 seconds while entering the digits or the control panel will
reject your PIN number.
"
If you make a mistake while entering your PIN, press the # key and start again.
"
An incorrect PIN will cause the keypad to beep 5 times.
"
The default master PIN is 1 2 3 4
After an alarm occurs
!
! !
! !
! !
! !
! !
! !
! !
!
#
Enter your PIN and push the # key. This will silence the buzzer and siren. It will not switch
the fence off. One of the ALARM lights will flash or stay on to indicate the type of alarm.
Investigate the cause of the alarm and correct it. After the ALARM light stops flashing enter
your PIN and push the # key to clear the alarm memory.
Change the voltage on the fence
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! $ $ $ $
3 #
Enter your PIN and push the
$
key, enter the digit “3”, then push the # key. The keypad
will beep three times to confirm the fence is in low voltage mode. When the fence is on
and in low voltage mode then the red ON light will flash. The red ON light will stay on if the
fence is in high voltage mode.
Bypass the fence alarm
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! $ $ $ $
1 #
Enter your PIN and push the
$
key, enter the digit “1”, then push the # key. The keypad
will beep 3 times and the FENCE ALARM light will start flashing slowly to confirm the fence
alarm is bypassed. To cancel the bypass, repeat the same sequence of keys.
Bypass the siren and strobe light (Silent alarm)
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! $ $ $ $
4 #
Enter your PIN and push the
$
key, enter the digit “4”, then push the # key. The keypad
will beep 3 times to confirm the siren and strobe light is bypassed. The beeper in the
keypad and energiser unit will still be active.
Un-bypass the siren and strobe light
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! $ $ $ $
7 #
Enter your PIN and push the
$
key, enter the digit “7”, then push the # key. The keypad
will beep twice to confirm the siren and strobe light is NOT bypassed.
Make the gate alarm immediate
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ⌧ ⌧ ⌧ ⌧
7 #
Enter your PIN and push the
⌧
key, enter the digit “7”, then push the # key. The keypad
will beep twice and the GATE ALARM light will start flashing very slowly (every 5 seconds)
to confirm the gate alarm is immediate.
Using your Merlin Keypad
3
Make the gate alarm delayed
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ⌧ ⌧ ⌧ ⌧
4 #
Enter your PIN and push the
⌧
key, enter the digit “4”, then push the # key. The keypad
will beep twice to confirm the gate alarm is delayed. The default gate delay is 4 minutes.
Bypass the gate alarm
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ⌧ ⌧ ⌧ ⌧
#
Enter your PIN and push the
⌧
key, then push the # key. The keypad will beep 3 times
and the GATE ALARM light will start flashing slowly to confirm the gate alarm is bypassed.
To cancel the bypass, repeat the same sequence of keys.
Turn the gate chime On / Off
⌧ ⌧ ⌧ ⌧
#
Push the
⌧
key, then push the # key. The keypad will beep twice to confirm the gate chime
is turned off and three times if it’s turned on. If the chime is on then the keypad will beep
twice if the gate closes and three times if it opens.
Bypass the service alarm
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! # # # #
9 #
Enter your PIN and push the
#
key, enter the digit “9”, then push the # key. The keypad
will beep 3 times and the SERVICE ALARM light will start flashing slowly to confirm the
service alarm is bypassed. To cancel the bypass, repeat the same sequence of keys.
Standby battery test
# # # #
6 #
Push the
#
key, enter the digit “6”, then push the # key. The keypad will beep twice and
start testing the battery. The default battery test duration is 5 minutes.
Changing a user PIN Master PIN
!
! !
! !
! !
! !
! !
! !
! !
! #
# #
#
0 #
User (1-6)
! ! ! !
#
New PIN
!
! !
! !
! !
! !
! !
! !
! !
!
#
New PIN
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
#
Enter your master PIN, push the
#
key, enter the digit “0”, then push the # key. Enter the
user number (1-6), and push the # key. User number 1 is the master PIN. Enter that user’s
new PIN and push the # key. Enter the new PIN again and push the # key. If the new PIN
is accepted, the keypad will beep twice. If you make a mistake while programming, or if the
system rejects the new PIN, the keypad will beep five times. The default master user PIN is
1 2 3 4.
Key Definitions
! ! ! !
Four digit Personal Identification Number (PIN)
⌧
Gate function key.
Panic Button. Keep in for 3 seconds.