background image

 

 

 

Page | 6 

 

P: 419.542.7751    F: 419.542.6690   800.782.761   nemcofoodequip.com 

 

 

 

49232A 

Power Settings/Cooking Guide

 

The ‘Best’

 Power Settings will vary depending on the range model number, the type and 

shape of the pan being used, as well as the type and quantity of food being cooked or 
held.  

Until you get a ‘feel’ for the unit, you should start at medium settings of 5

 or 6 and 

adjust up or down from there to get the performance you want.   
 
You can use the following as a starting guide: 
 
1.

 

 Stir Fry:  Quickly stir fry on high heat settings of 8, 9 or 10. 

2.

 

Boil Water:  Boil water on high heat settings of 9 or 10, then reduce to level 5 or 6 to 
maintain a hard boil.  Reduce to 3 or 4 for a slow boil. 

3.

 

Pan Fry:  Pan fry on medium to high heat settings of 5 to 10. 

4.

 

Sauté/Simmer:  Use medium to low settings 3 to 5. 

5.

 

Warming:  Hold food at serving temperatures using setting H1 thru H7.  Results will 
vary depending on the volume of food being held. 

6.

 

Chocolate Melting:  Use setting H1. 

 

The Holding or warming settings H1 thru H7 approximate the following temperatures .  Results 

will vary depending on the type of pan, the type and volume of food being held, and the model 

number of the range being used. 

 

 

Warmer 
Setting 

Temp 

o

95 

105 

122 

140 

160 

180 

195 

 

 
 
 
 
 

Содержание , 9132A-1














Отзывы: