:
i
j
V
:
i
j
:
i
j
:
i
j
J
Ò
:
i
j
:
i
j
ÿ
O
:
ä
6
:
Z
:
i
j
C
i
j
:
O
:
O
C
C
11
What to do if ...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
–
Start
/Pause
not selected?
– Tap not turned on?
– Filter blocked? Clean the filter ->
page 10
.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Programme stopped? ->
page 4
.
–
c
(without final spin) selected?
-> page 3, 4.
– Can be opened by emergency release only?
-> page 9.
ʑ
Programme does not
start.
–
Start
/Pause
or
(Finished in)
time selected?
– Washing machine door closed?
– Childproof lock active? Deactivate ->
page 5
.
ʑ
Detergent solution is not
drained.
–
c
(without final spin) selected?
-> page 3, 4.
– Clean the detergent solution pump ->
page 10
.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Spin result not
satisfactory.
– Distribute large and small items of laundry evenly in the drum.
–
(Easy-iron)
selected?
–> page 5.
– Selected speed too low?
–> page 5
.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary ->
page 9
.
ʑ
Odour formation in the
washing machine.
– Run programme
Cottons
90 °C
without laundry. Use
standard detergent.
ʑ
Status display
³
þ
flashing.
Appliance has detected
a detergent overload.
– Too much detergent used?
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour
into compartment
II
(not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and
“wandering” during the
spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet
–> Installation instructions
.
– Transportation safety devices removed?
Remove the transportation safety devices
–> Installation
instructions
.
ʑ
Display panel/indicator
lamps do not function
during operation.
– Power cut?
– Fuses triggered? Reset/change the fuse.
– If the fault occurs repeatedly, call customer services.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced load detection system adjusts
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues
on the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Use the
Rinse
cycle or brush out the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to
Off
and remove the mains plug from the socket.
– Turn off the water supply and call customer services
–> Installation instructions.
