Please detach and keep
Instructions for the installer
This appliance must be installed in a place
with the proper level of ventilation. The gases
produced during combustion must be released
to the outside.
Check the size of the hob and the size of
the opening to be made on the kitchen unit.
The panelling on the work surface in the
immediate vicinity of the hob must be made of
non-flammable material. Both stratified coatings
and the adhesive used to fix them in place
must be heat resistant. Otherwise, they may
be damaged.
Electric wiring must not come into contact
with hot areas
The mains supply cable must be fixed to
the kitchen unit to prevent it from coming into
contact with hot parts on the oven or hob.
Appliances with electric components must
be earthed.
Handle the appliance with care throughout
the entire installation process. Avoid knocking
the appliance.
This appliance shall be installed in
accordance with the regulations in force
and only used in a well ventilated location.
Read the instructions before installing or
using this appliance.
SHOULD THE RELEVANT CONDITIONS
NOT BE PROPERLY SATISFIED, THE
INSTALLER, AND NOT THE
MANUFACTURER, SHALL HELD LIABLE.
Installing the hob in the
kitchen unit
The positioning of a hob in a kitchen unit
is Class 3 according to the standard for gas
Housing measurements
1- Minimum Distances (mm). Cut a hole of
the necessary size in the work surface, Fig. 1.
For installation on top of an oven, check
the size of the oven as given in its assembly
manual.
Centre the hob in the hole on the work
surface.
4- The end of the input collector on gas
hobs comes with a
1/
2
In either of the cases, do not move or twist the
L-tube from its factory-set position.
To use this appliance in France, it is necessary
to remove the L-tube mounted in the factory
and assemble the one supplied in the accessory
If, for some reason, the L-tube should be twisted,
it is necessary to make sure that this area is
properly sealed. Make sure that all connections
performed are free of leakage.
The manufacturer does not accept any
liability for leakage on connections performed
by the installer or if the L-tube is moved or
twisted.
5- Check the voltage and total power on
the characteristics plate. The appliance must
be EARTHED.
Make sure that connection has been
performed in accordance with legal regulations
in force for the country in question. Comply
fully with the conditions laid down by the local
electricity company.
In order to meet normal safety standards,
the installer must supply an all-pole circuit
breaker with a contact aperture of at least 3
mm. This is not necessary when connection is
made via a socket, so long as this is accessible
to the user.
Appliances equipped with plugs should
only be connected to sockets which are duly
earthed.
The appliance is type "Y". This means that
the input supply cable cannot be changed by
the user. Only the brand's service technicians
are qualified to replace this cable. Use the right
cable type and section.
Do not tamper inside the appliance. If
necessary, call our Service Centre.
Hobs with control knobs are supplied with
a plugged or unplugged power cable.
TYPES OF CABLE
All gas
3 x 0.5 mm
2
Electric plate 1 kW
3 x 0.75 mm
2
Electric plate 1.5 kW
3 x 1
mm
2
6-In order to complete the installation
process, you must place the diffusers and the
tops of the burners on their corresponding
burners. Also you must place the metal grids
Changing the type of gas
*Before connecting the appliance to the
supply, check that it is prepared for the type of
gas in question. Our hobs leave the factory set
for the gas type indicated on the characteristics
plate.
Depending on the regulations in force in
your country, this hob may be adapted to work
with other types of gas (see characteristics
plate). To adapt the gas type, proceed as
follows:
A ) Changing the injectors on the burners
1 -Remove the grates, covers and burner
core.
2 -Change the injectors using a 7-mm
socket wrench and be sure to tighten them
down properly so that they are fully air-tight.
It is not necessary to adjust the primary air
on these burners.
B ) Adjusting reduced consumption on
the burner valves.
1 - Set the valves to minimum.
2 - Remove the control knobs from the
• If your hob only has inner seals made of soft
plastic, dismount these by levering around
them with a screwdriver to access the
adjustment screw.
4 -Adjusting the by pass screw.
•For Propane and Butane Gas: the screw must
be tightened down fully.
•For Natural Gas: turn the screw in an anti-
clockwise direction until the correct release of
gas is reached: when the burner is changed
from the maximum to minimum settings, the
5 - Re-assembling the anti-liquid seals. All
6 - Re-assemble the control knobs.
.
3 -
flame does not go out or backfire
.
Do not remove the disc seal
2- The chipboard used to make the worktops
tends to swell quite quickly when it comes into
contact with moisture. Thus we recommend
protect them from steam
Depending on the model, the clips and the
watertight seal (lower edge of the cooking hob)
may already be fitted; if this is the case, do not
remove them under any circumstance.
3- For disassembly, unscrew the clip and
proceed in the reverse manner.
from below upwards.
Power cable:
Cooking hob:
If the cooking hob is to be installed above
to the assembly manual.
ventilation, and check the dimensions
according
an oven, check that the oven is fitted with
power
The seal ensures that the entire work
surface will be watertight, and prevents water
seepage.
If this item has not been fitted in the factory,
remove the pan supports and the gas burner
covers and diffusers from your cooking hob,
At the same time, press down on the hob
edges to ensure that the cooking hob is
If your cooking hob model comes with the
and turn it upside down. Now fit
seal supplied with the
the adhesive
appliance onto the
lower edge of the cooking
the
accessories bag and
points designed for
place them in the holes provided for this purpose
remove
hob, depending on
clips
screw
them into the lower
this
or
the model Fig 2a/2b
purpose, depending on the model Fig. 3d.,
according to the clip model Fig. 3a or Fig. 3b.
supported all the way round Fig. 4.
• If your clip is type Fig. 3a you should push
• If your clip is type Fig. 3b you should use
the hob is fitted you should turn the clip and
a screwdriver to lever it upwards Fig. 3c.
bag. Fig.
5
a. Do not forget to insert the seal.
Fig.
7.
valve shafts. Fig.
8.
9
from
the attached
clip type which corresponds to Fig. 3d., once
tighten the screw as shown in Fig. 3e.
If no oven is installed under an
electrical or
mixed
(gas and electric) hob, place a
separator of non-flammable material e.g.
plywood or metal at a distance of 10 mm.
from the bottom of the hob to prevent access
to the lower part of the hob.
If no oven is installed under a
gas
hob, it is
suggested to place a separator of non-
flammable material e.g. plywood or metal at
a distance of 10 mm. from the bottom of the
hob to prevent access to the lower part of the
hob.
In the event that a drawer is located beneath
the appliance, please make sure that the
drawer contains no heat-sensitive or easily
combustible objects, such as spray cans or
shoe polish. Use a heat-resistant utility drawer
only.
appliances EN 30-1
.
-1
corre
c
tly on their supporting elements.
Fig.
6.
treating the cut edges with a special glue, to
or any condensation
that might drip down beneath the cooker
unit's work surface.
gas the appliance has been adapted to
near the characteristics plate.
of
C) Put the label which indicates the type
en
All installation, regulation and adaptation to
other types of gas must be carried out by an
authorised installation technician,
respecting all applicable regulations,
standards and the country's electrical and
gas supply companies' specifications.
It is recommended that you call our
Technical Assistance Service for adaptation
to other types of gas. Before you begin, turn
off the appliance's electricity and gas supply
.
All installation, regulation and adaptation to
other types of gas must be carried out by an
authorised installation technician,
respecting all applicable regulations,
standards and the country's electrical and
gas supply companies' specifications.
It is recommended that you call our
Technical Assistance Service for adaptation
to other types of gas. Before you begin, turn
off the appliance's electricity and gas supply
.
Before connecting the appliance to the
supply, check that it is prepared for the type of
plate.
the
characteristics
factory set
gas in question.
Our hobs leave the
for the gas type indicated on
(Table I).
(Table II)
”
threaded L-tube,
(20,955 mm)
parts on the housing (e.g. drawers) and passing
•Connection to a flexible metal tube
•Rigid connection.
avoid both contact between this tube and moving
(L min.1m - max.3m). If this method is used,
Fig.
5
. This caters for:
the tube through spaces liable to get blocked.
against the spillage of liquids on the hob.
the water-tightness of the electricity system
in the event of damage, change the entire valve.
the seals must be in place in order to ensure
Never dismount the valve shaft (Fig. 10):
Содержание T63S46S0
Страница 2: ...x4 a b c b a 2 2 3 3 3 3d...
Страница 3: ...a 3 4 5 5 e max 12 4...
Страница 4: ...7 mm 7 8 9 6 10...