NEFF I96BMV5N5, Инструкция по установке и эксплуатации

Страница: 9 / 25

Imp
ort
Ap
plia
nce
s.c
om
THE EASIEST WAY TO SELF-IMPORT APPLIANCES DIRECT FROM EUROPE.
en
Operating the appliance
8
Fan run-on time
Switching on
Touch the
(
symbol while the fan is running at fan
setting 1.
The fan will run at fan setting 1.
The fan will switch off automatically after
approximately 10 minutes.
Switching off
Touch the
)
symbol to select a different fan setting.
This immediately stops the fan run-on.
Automatic mode
Switching on
1.
Touch the
#
symbol.
The fan will start at setting
ƒ
.
2.
Touch the
‘
symbol.
The optimum fan setting is set using an automatic air
sensor.
Switching off
Touch the
‘
or
#
symbol to switch off automatic mode.
The fan will switch itself off automatically if the
automatic air sensor detects no further change in the air
quality in the room.
Automatic mode can run for a maximum of 4 hours.
Sensor control
In automatic mode, an automatic air sensor in the
extractor hood detects the intensity of the cooking and
roasting odours. Depending on the setting of the
automatic air sensor, the fan automatically switches
itself to another fan setting.
Possible sensor settings:
Default sensitivity setting:
†
Lowest sensitivity setting:
‹
Highest sensitivity setting:
Š
If the sensor control responds too strongly or not
enough, it can be changed accordingly:
1.
Touch and hold the
‘
symbol for 1 second when the
fan is switched on. The setting will be displayed.
2.
The sensor controller setting can be changed by
touching the
(
or
)
symbol.
3.
Take your finger off the
‘
symbol.
Lighting
The lighting can be switched on and off independently
of the fan.
Touch the
6
symbol.
Setting the brightness
Press and hold the
6
symbol until the required
brightness is reached.
Saturation display
If the metal grease filters or the activated charcoal filter
are/is saturated, the corresponding symbols flashes
after the appliance is switched off:
■
Metal grease filter:
”ªª
■
Activated charcoal filter:
’ªª
■
Metal grease filter and activated charcoal filter:
”ªª
and
’ªª
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced.
~
"Cleaning and maintenance" on page 12
Note:
The saturation indicator does not apply for non-
renewable activated charcoal filters that are inserted
downstream of the metal grease filter. These activated
charcoal filters must be replaced twice a year.
The saturation indicators can be reset while they are
flashing. To do this, touch the
(
symbol.
Switching over the display for air circulation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■
The extractor hood must be connected and switched
on.
■
Touch and hold the
Q
symbol and touch
the
(
or
)
symbol until "2" lights up for air
recirculation mode (filters that cannot be
regenerated). Take your finger off the
Q
symbol.
This will switch the electronic controller over to air
recirculation mode (filters that cannot be
regenerated).
■
Touch and hold the
Q
symbol and touch
the
(
or
)
symbol until "3" lights up for air
recirculation mode (filters that can be regenerated).
Take your finger off the
Q
symbol. This switches the
electronic controller over to air recirculation mode
(filters that can be regenerated).
■
Repeatedly touching and holding the
Q
symbol and
touching the
(
or
)
symbol until "1" lights up switches
the electronic controller back over to air extraction
mode.
Audible signal
Switching on
Touch and hold the
#
and
Q
symbols at the same time
for approximately 3 seconds when the fan is switched
on. An audible signal will sound as an
acknowledgement.
When the signal tone is activated,
‚
will be lit.
Switching off
Touch and hold the
#
and
Q
symbols at the same time
for approximately 3 seconds when the fan is switched
on. An audible signal will sound as an
acknowledgement.
When the signal tone is deactivated,
‹
will be lit.