NEFF D96BMV5N5B, Инструкция по установке и эксплуатации

Страница: 8 / 24

en
Operating the appliance
8
Fan run-on time
Switching on
Touch the
A
symbol while the fan is running at fan
setting 1.
The fan will run at fan setting 1.
After approximately 10 minutes, the fan will switch itself
off automatically.
Switching off
Touch the
@
symbol to select a different fan setting.
This immediately stops fan run-on.
Automatic mode
Switching on
1.
Touch the
#
symbol.
The fan will start at setting
ƒ
.
2.
Touch the
‘
symbol.
The optimum fan setting is set using an automatic air
sensor.
Switching off
Touch the
‘
or
#
symbol to switch off automatic mode.
The fan will switch itself off automatically if the
automatic air sensor detects no further change in the air
quality in the room.
Automatic mode can run for a maximum of 4 hours.
Sensor control
In automatic mode, an automatic air sensor in the
extractor hood detects the intensity of the cooking and
roasting odours. Depending on the setting of the
automatic air sensor, the fan automatically switches
itself to another fan setting.
Possible sensor settings:
Default sensitivity setting:
†
Lowest sensitivity setting:
‹
Highest sensitivity setting:
Š
If the sensor controller responds too strongly or not
enough, it can be changed accordingly:
1.
Touch and hold the
‘
symbol for 1 second when the
fan is switched on. The setting will be displayed.
2.
The sensor controller setting can be changed by
touching the
@
or
A
symbol.
3.
Take your finger off the
‘
symbol.
Lighting
The lighting can be switched on and off independently
of the fan.
Touch the
6
symbol.
Setting the brightness
Press and hold the
6
symbol until the required
brightness is reached.
Saturation display
If the metal grease filters or activated charcoal filter are/
is saturated, the corresponding symbols will flash once
the appliance has been switched off:
■
Metal grease filter: ”ªª
■
Activated charcoal filter: ’ªª
■
Metal grease filter and activated charcoal filter:
”ªª
and
’ªª
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced.
~
"Cleaning and maintenance" on page 12
The saturation indicators can be reset while they are
flashing. To do this, touch the
A
symbol.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■
The extractor hood must be connected and switched
on.
■
Touch and hold the
Q
symbol and touch the
@
or
A
symbol until "2" lights up for air recirculation mode
(filters that cannot be regenerated). Take your finger
off the
Q
symbol. This will switch the electronic
controller over to air recirculation mode (filters that
cannot be regenerated).
■
Touch and hold the
Q
symbol and touch the
@
or
A
symbol until "3" lights up for air recirculation mode
(filters that can be regenerated). Take your finger off
the
Q
symbol. This will switch the electronic
controller over to air recirculation mode (filters that
can be regenerated).
■
Repeatedly touching and holding the
Q
symbol and
touching the
@
or
A
symbol until "1" lights up
switches the electronic controller back over to air
extraction mode.
Audible signal
Switching on
Touch and hold the
#
and
Q
symbols at the same
time for approximately 3 seconds when the fan is
switched on. An audible signal will sound as an
acknowledgement.
When the signal tone is activated,
‚
will be lit.
Switching off
Touch and hold the
#
and
Q
symbols at the same
time for approximately 3 seconds when the fan is
switched on. An audible signal will sound as an
acknowledgement.
When the signal tone is deactivated,
‹
will be lit.