10
Checking, correcting or deleting settings
1.
To check your settings, press the
KJ
clock function button
repeatedly until the corresponding symbol lights up.
2.
If necessary, you can correct your setting using the rotary
selector.
3.
If you wish to cancel your setting, turn the rotary selector anti-
clockwise to the original value.
Changing the basic settings
Your appliance has various basic settings which you can
change at any time.
Basic settings
In the table, you will find all the basic settings and options for
changing them.
Press the main switch. The appliance is ready for operation and
the
~
symbol lights up.
1.
Press and hold the
o
button for a few seconds.
The first basic setting appears on the clock display.
2.
Press the
o
button repeatedly until the required basic setting
is shown.
3.
Make the desired setting using the programme selector.
4.
Finally, press and hold the
o
button for a few seconds.
All settings are applied.
You can change the settings at any time.
Care and cleaning
With careful care and cleaning your microwave oven will retain
its looks and remain good order. We will explain here how you
should care for and clean your appliance correctly.
:
Risk of short circuit!
Never use high-pressure cleaners or steam cleaners to clean
the oven.
:
Risk of burns!
Never clean the appliance immediately after switching off. Let
the appliance cool down.
Notes
■
Slight differences in colour on the front of the appliance are
caused by the use of different materials, such as glass,
plastic and metal.
■
Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
■
Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
■
Unpleasant odours, e.g. after fish has been prepared, can be
removed very easily. Add a few drops of lemon juice to a cup
of water. Place a spoon into the container as well, to prevent
delayed boiling. Heat the water for 1 to 2 minutes at
maximum microwave power.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use:
■
any caustic or abrasive cleaning agents,
■
metal or glass scrapers to clean the glass in the appliance
door,
■
metal or glass scrapers to clean the door seal,
■
hard scouring pads and sponges,
■
cleaning agents with high concentrations of alcohol.
Rinse out new sponge cloths thoroughly before use.
For easier cleaning, you can switch on the oven light. Open the
appliance door to do so.
Basic setting
Options
Explanation
™‚
Audible signal duration:
‚
= short = 10 seconds
Audible signal duration:
ƒ
= medium = 2 minutes
„
= long = 5 minutes
Signal after the cooking time has elapsed
™ƒ
Button tone:
‚
= on
Button tone:
ƒ
= off
Confirmation tone when a button is pressed
Area
Cleaning agents
Appliance front
Hot soapy water:
Clean using a dish cloth and then dry
with a soft cloth. Do not use glass clean-
ers or metal or glass scrapers for clean-
ing.
Stainless steel
Hot soapy water:
Clean using a dish cloth and then dry
with a soft cloth. Remove traces of
limescale, grease, starch and albumin
(e.g. egg white) immediately. Corrosion
can form under such residues. Special
stainless steel cleaning agents can be
obtained from the after-sales service or
from specialist retailers.
Cooking compart-
ment made of stain-
less steel
Hot soapy water or a vinegar solution:
Clean using a dish cloth and then dry
with a soft cloth.
If the oven is very dirty: use oven
cleaner, but only when cooking com-
partment is cold. It is best to use a stain-
less-steel sponge. Do not use oven
spray or other aggressive oven cleaners
or abrasive materials. Scouring pads,
rough sponges and pan cleaners are
also unsuitable. These agents scratch
the surface. Allow the interior surfaces
to dry thoroughly.
