Nedap MACE MM QR Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 30

Nedap MACE MM QR Скачать руководство пользователя страница 8

MACE | INSTALLATION GUIDE

Connections

8/30

3.2.3

WIEGAND

The Wiegand and Magstripe ISO7811/2 (clock & data) interface share the same
connections. This means that only Wiegand or Magstripe can be used and not both
simulaneously.

Wiegand connections:

GRAY

D0

PINK

D1

BLACK

Ground (0V)

SHIELD

Shield connected to DC-ground.

Message format:
The Wiegand output format is determined by the programming format of the
credential. MACE Wiegand credentials will automatically generate a Wiegand
message. If the credential is not programmed in Wiegand format, you may configure
the message output format as described in chapter 4.5.2.

Make sure to order the correct credential programming format if you want to use the
Wiegand or Magstripe interface. See also the MACE how to order guide (HTOG) for
more information.

Wiegand Timing
In the figure below the Wiegand protocol timing is specified.

Tpw

5V
0V

D1

5V
0V

D0

Tpi

Tpi

Tpw

Figure 3: Wiegand protocol timing

Timing constants:
Tpi

Pulse interval time

1msec

Tpw

Pulse width time

50µsec

Note

Extending these
connections beyond the 5
meter pig tail length shall
ONLY be allowed using
shielded cable (4 x 0.25
mm2) as long as the total
length is shorter than 150
meters (500 feet).
The shield shall be
connected to the metal
case of the external device.

«
...
6
7
8
9
10
...
»

Содержание MACE MM QR































Отзывы:

Нет отзывов