background image

NECTA SPA TECHNICAL MANUAL “COLIBRÌ” 

 

Service Manual: Colibrì  

 

 

 

Edition 02-2002  

 

 

 

 

 23 /25

 

DAILY CLEANING AND HYGIENE 

(Expected time 3 min. 30 sec.) 

 

Open the door and disconnect the 
machine from the power supply 

(FIG 1) 
Remove the liquid collection 

container, empty it and rinse it 
thoroughly (FIG 2) 
Empty the grounds container and 

rinse it thoroughly 
Remove the powder dispensing 

spouts and clean thoroughly using 
specific hygiene products (FIG 3) 

If 

necessary

, remove the 

containers, empty them completely 
and clean thoroughly 

Remove the liquid collection 
container and the grounds 

container, empty and clean them 
Remove the coffee unit, clean and 
rinse with a sponge damp with hot 

water. (FIG 4) 
Remove the sugar dispensing spout 

and clean thoroughly (FIG. 6) 
Remove and clean the cup shift 

(FIG. 5) 
Remove and clean the dispensing 
spout assembly 

Reassemble all parts, taking care 
not to touch with your hands any 

parts that come into contact with 
food. 
Close the door and make some test 

selections. 
Carry out a mixer automatic wash 

cycle according to the pre-set 
procedures. 

Note: After restarting the machine 
remember to reset the solid waste 
container by removing it and 

reinserting it again.

 

 

FIG. 5 

FIG.1

 

FIG. 2 

FIG. 7 

FIG. 6

FIG. 3 

FIG. 4

Содержание Colibri


























Отзывы: