background image

NEAX 2000 IPS Configuration Guide

Page 86 

NDA-24347, Issue 1

Traffic Capacity Chapter 8  System Capacity

Traffic Capacity

Note: 

The maximum traffic load of each FP is 2,500 BHCA. 

System-based Device Registration Server (DRS)

Table 8-6    Traffic Capacity

NUMBER OF PIMS 1 PIM 2 PIM 3PIM 4PIM 5 PIM 6 PIM 7 PIM 8 PIM

Traffic Capacity 

Maximum

2,500 BHCA

Maximum

5,000 BHCA

Note

 

Maximum

7,500 BHCA

Note

 

 

Maximum

8,000 BHCA

Note

 

 

Table 8-7    System-based Device Registration Server (DRS)

FEATURES OF BUILT-IN DRS

DESCRIPTION

REMARKS

Maximum Registration Terminals

512 ports per MP

Log-in

Login without password

Not Available

Use blank as a password

Authentication by Network-based DRS

Not Available

Authentication by System-based DRS

Available

Authentication by MAC Address

Available

Confirmation when overriding

Available

Log-out

Dialing Log-out feature access code

Available

Function key

Available

Softkey

Available

DHCP

Inter-working with DHCP server

Available

TCP PORT NUMBER

MAT

60000 (Fixed)

OAI

60030 (Fixed)

Содержание UNIVERGE NEAX 2000 IPS

































































































Отзывы: