NEC startWARE-GHS-Ravin-E Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 40

background image

13

User’s Manual U17316EE1V0UM00

Chapter 1

Introduction

1.1 System

Requirements

1.2 Package

Contents

Please verify that you have received all parts listed in the package contents list attached to the
startWARE-GHS-Ravin-E package. If any part is missing or seems to be damaged, please contact the
dealer from whom you purchased your startWARE-GHS-Ravin-E.

Note: Updates to this User Manual, additional documentation and/or utilities for

startWARE-GHS-Ravin-E, if available, may be downloaded from the NEC WEB page(s):

http://www.nec.de/support

.

1.3 Related

Documents

Ravin-E Preliminary Data Sheet, NEC Doc. Number S15521EJ1V0DS00

startWARE-GHS-V

R

4131 User’s Manual, NEC Doc. Number U16417EE1V0UM00

startWARE-GHS-V

R

4133 User’s Manual, NEC Doc. Number U16916EE2V0UM00

Application Note:

Operation of Ravin-E with V850 Devices
NEC Doc. Number S17194EE1V0AN00

Motherboard:

startWARE-GHS-Ravin-E is an add-on board designed for the startWARE-GHS-
V

R

4131/33 boards. Running the startWARE-GHS-Ravin-E board with other mother-

boards will require a suitable adapter, which is not part of this package. Such adapters
are not available from NEC and therefore have to be provided by the user.
Alternatively the startWARE-GHS-Ravin-E board can be operated via its PCI interface.
That will require a suitable adapter whose schematics are included in chapter 5.4 of
this document. Note that the PCI interface uses 3 V signaling only and it can therefore
not be operated in a normal PC.

«
...
11
12
13
14
15
...
»

Содержание startWARE-GHS-Ravin-E









































Отзывы:

Нет отзывов

Похожие инструкции для startWARE-GHS-Ravin-E

Бренд: IEI Technology Страницы: 21

Бренд: Pima Страницы: 4

Бренд: Measurement Computing Страницы: 27

Бренд: ESD Страницы: 28

Бренд: Grizzly Страницы: 9

XM24 Expansion Module

Бренд: Avaya Страницы: 5

Бренд: RAIDAGE Страницы: 60

Бренд: ZKTeco Страницы: 68

Бренд: AMD Страницы: 45

Бренд: Loopcomm Страницы: 2

Бренд: VideoWave Страницы: 12

Бренд: Alcatel-Lucent Страницы: 60

Бренд: Telit Wireless Solutions Страницы: 79

Бренд: M86 Security Страницы: 512

Бренд: Commell Страницы: 17

FaxFinder FF-120

Бренд: Multitech Страницы: 20

Бренд: Icop Страницы: 31

JOBAID T200 IDSL

Бренд: ADTRAN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды