background image

ISSUED: 08-05-08  SHEET #: 056-9008-1

Visit the Peerless Web Site at www.peerlessmounts.com

2 of 10

For customer care call 1-800-865-2112 or 708-865-8870.

Table of Contents

Parts List .................................................................................................................................................................... 3

Installation to Extension Columns / Ceiling Plate ........................................................................................................ 4

Installation to Wood Joist Ceilings .............................................................................................................................. 5

Installation to Concrete Ceilings .................................................................................................................................. 6

Installation to Threaded Rods ...................................................................................................................................... 7

Attaching Adapter Plate to Projector ........................................................................................................................... 8

Attaching Adapter Plate to Projector Mount ................................................................................................................ 9

Projector Alignment ................................................................................................................................................... 10

Tools Needed for Assembly

• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 1/4" bit for concrete surface
• 5/32" bit for wood studs
• open end wrench
• level

• It is the responsibility of the installer to ensure that the

projector is properly ventilated.

CAUTION

NOTE: Read entire instruction sheet before you start installation and assembly.

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings con-

tained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless
customer care at 1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

• Never exceed the Maximum Load Capacity.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power. See suggested torque values where applicable within these instructions.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

WARNING

Содержание NP300 XGA











Отзывы: