NEC NEC MultiSync LCD1550V LCD1550V LCD1550V Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 101

background image

5-7

3. Safety Tests

Perform the following inspection tests in accordance with the standards set forth in Common Electrical
Safety Inspection Standards for Information Processing Device & Office Equipment (DSQS-009-103).

Destination :

World wide

Applicable Regulations :

UL1950, CSA C22.2 No 950 (C-UL), DHHS, TUV (EN60950), CE, PTB

Classification :

Class I device (with safety ground), movable

Ratings :

AC 100-240V, 50/60Hz,

Unless otherwise specified, rating voltage is 240V.

3.1 Ground Continuity

( It is applied to the PSU built-in set. )

Perform the test at the points indicated below and make sure that the ground continuity values are within
the prescribed range. (This test is to be performed before the electric strength test.)

1) The Ground Line of inlet shall be satisfied indicated below.

a) The color of Ground Line is spiral of green and yellow.

b) The Ground Line is connected at specified point on the chassis base with specified screw.

2) Measurement Point- Between the ground terminal of power supply cord and the chassis Screw

The standard for a decision : Less than 0.1ohm. ( Input current 25A)

3.2 Electric Strength

( It is applied to the PSU built-in set. )

Perform the tests at the points indicated below and make sure that there is no dielectric breakdown or
flashing.

Measurement Points

Make measurements between the power supply terminals (other than the ground terminal) and each
of the following points : (See note below.)

Signal cable connector shell

Chassis base

Note : The two terminals other than the ground terminal (power supply cord) must be shorted out.

The standard for a decision : Less than 10mA. ( Input voltage 1500V AC )

«
...
51
52
53
54
55
...
»

Содержание NEC MultiSync LCD1550V LCD1550V LCD1550V






































































































Отзывы:

Нет отзывов

Похожие инструкции для NEC MultiSync LCD1550V LCD1550V LCD1550V

BrilliantVIEW SEW-3041W

Бренд: Samsung Страницы: 9

SyncMaster VC240

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 2

Weather Monitor II

Бренд: DAVIS Страницы: 5

Бренд: Yamaha Страницы: 20

Бренд: Panasonic Страницы: 24

Viera TH-42PHD5

Бренд: Panasonic Страницы: 40

Toughbook CF-VDW07

Бренд: Panasonic Страницы: 80

Бренд: AOC Страницы: 93

SM-5000 - COMPUTER

Бренд: Yaesu Страницы: 8

Бренд: Vitek Страницы: 2

Caneo 43 Hygienic Series

Бренд: Captron Страницы: 14

UltraView HAP15AV

Бренд: I-Tech Страницы: 28

Бренд: Good Display Страницы: 17

Бренд: Arestech Страницы: 23

UltraView AP-26W

Бренд: I-Tech Страницы: 32

Бренд: ACRONIS Страницы: 25

Бренд: Ditel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды