background image

7 of 7

ISSUED: 07-28-10  SHEET #: 125-9132-1

© 2010, Peerless Industries, Inc. All rights reserved.

All other brand and product names are trademarks or registered trademarks of their respective owners.

Mounting and Removing Flat Panel Screen

DETAIL 1

fig 4.1

For preset tilt angles use Increlok

™ and for custom tilt

angle use ratchet handle.

INCRELOK

: The screen can be locked into a

pre-set tilt position of -5

°

, 0

°

, 5

°

, 10

°

 or 15

°

. Use

locator hole to find tilt position hole and tilt screen to
align holes. Tighten IncreLok™ tilt locking screws on
both tilt brackets to lock tilt as shown in detail 1.

Ratchet Handle:

 

Loosen ratchet handle (refer to step

3 for tension adjustment of handle). 

Push or pull from

top or bottom of screen to adjust tilt as shown in figure
4.1. The tilt can be adjusted to a maximum of 15°
forward or 5° backward.

Tension Adjustment of Ratchet Handle:

 Adjust

tension in tilt brackets (B & C) by rotating ratchet
handle. NOTE: If obstruction prevents ratchet handle
from rotating, pull handle out while turning will allow
handle to reposition without tightening. Release and
turn handle to tighten or loosen.

Mounting Screen: Ratchet handle must be in the up or
down position or interference will occur while hooking tilt
brackets to wall plate (A). Slowly hook tilt brackets (B
& C
) onto wall plate (A) and swing screen down as
shown in fig. 3.1. Tilt bracket hooks must fully engage
wall plate. Using phillips screw driver or security allen
wrench (F), turn safety/security screws on tilt brackets
(B & C) clockwise till screw tip securely contacts wall
plate as shown in cross section.

Screen Adjustment: Screen can be adjusted
horizontally by loosening safety/security screws on tilt
brackets (B & C) three full turns. Adjust screen as
shown in figure 3.2. Tighten safety/security screws on
tilt brackets till screw tip securely contacts wall plate
as shown in cross section.

Removing Screen: To remove screen from mount,
loosen safety screws, swing screen away from mount,
and lift screen off of mount.

4

Adjusting the Tilt Angle of the Flat
Panel Screen

• Always use an assistant or mechanical lifting equipment

to safely lift and position the flat panel screen.

• Do not tighten screws with excessive force. Overtightening

can cause damage to mount. Tighten screws to 40 in. • lb
(4.5 N.M.) maximum torque.

• Be careful not to pinch fingers when pushing screen from

the bottom.

WARNING

fig 3.2

IncreLok™

TILT LOCKING

SCREW

SAFETY/

SECURITY

SCREW

CROSS SECTION

A

B
&
C

fig 3.1

RATCHET

HANDLE

 LOCATOR

HOLE

RATCHET

HANDLE

Visit the Peerless Web Site at www.peerlessmounts.com                                                       For customer care call 1-800-729-0307 or 708-865-8870.

3

4

Содержание E551








Отзывы: