NEC CHIEF K3F220 Скачать руководство пользователя страница 2

Страница: 2 / 38

CHIEF STAND INSTALLATION MANUAL | USER’S GUIDE

Contents

General Information and Cautions 3

Chapter 1

Removing the Bezel

Purpose 4

How to Remove the Bezel 5

Chapter 2

2 x 2 Multi-Monitor Installation (K3F220/K3G220)

Model K3F220 (Self-Standing) 6

Model K3G220 (Desk Mounted) 7

Overview 8

Installing the Lower Left and Lower Right Monitors 9

Set the Vertical Arm Position 9

Attach the Monitors 10

Set the Horizontal Position 11

Installing the Upper Left and Upper Right Monitors 13

Adjust Tilt / Swivel / Pivot 16

Tilt the Upper Monitors 16

Face the Monitors Inside 17

Cable Connection Example 18

Cable Management 18

Chapter 3

3 x 2 Multi-Monitor Installation (K3G320)

Model K3G320 (Desk Mounted) 19

Overview 20

Installing the Center Monitors 21

Set the Center VESA Plates Position 21

Attach the Lower Center Monitor 24

Attach the Upper Center Monitor 25

Installing the Lower Left and Lower Right Monitors 27

Set the Vertical Arm Position 27

Attach the Lower Left and Lower Right Monitors 29

Set the Lower Left and Lower Right Horizontal Position 30

Installing the Upper Left and Upper Right Monitors 31

Completed Setup 32

Adjust Tilt / Swivel / Pivot 33

Facing the Monitors Towards Center 33

Tilt Down the Upper-Center Monitor (Not Recommended) 34

Cable Connection Example 35

Cable Management 36

Chapter 4

Unifying Multi-Picture Quality

The content of this manual is furnished for informational use only, is subject to change without notice, and should not be

construed as a commitment by NEC Display Solutions NEC Display Solutions assumes no responsibility or liability for

any errors or inaccuracies that may appear in this manual
Document revision: February 2017
CHIEF® is a registered trademark of Milestone AV Technologies

Содержание CHIEF K3F220






































Результаты поиска

Содержание CHIEF K3F220

Отзывы:

Бренды по названию

Популярные бренды

NEC CHIEF K3F220, Руководство по установке

Результаты поиска

Содержание CHIEF K3F220

Отзывы:

Бренды по названию

Популярные бренды