NEC Aspire L, Сетевое руководство

Страница: 54 / 256

Features
ARS/F-Route
44
◆
Networking
➻
26-02-02 : Dial Analysis Table for ARS - Service Type
For each Dial Analysis Table (1-200), select ‘0’ for no ARS, ‘1’ for Service Type 1 - Route to
Trunk Group Number to have the number route to a trunk group [Refer to Program 26-02-03]
or ‘2’ for Service Type 2 - F-Route Selected to have the dialed number controlled by the F-
Route table. If Service Type 2 is selected and F-Route operation is on, the F-Route table used
is determined by Program 44-04. If F-Route operation is off, the routing is determined by Pro-
gram 44-05.
➻
26-02-03 : Dial Analysis Table for ARS - Additional Data / Service Number
For each Dial Analysis Table (1-200), if Service Type 1 was selected in Program 26-02-02,
enter the trunk group number (0-100, 0=no route).
➻
26-03-01 : ARS Dial Treatments
Assign the Dial Treatments (1-15) for automatic ARS dialing translation. Assign Dial Treat-
ments to Service Numbers (Trunk Groups) in Program 26-02. The ARS Dial Treatment
options are:
● 3 - Delete the NPA if dialed as part of the initial call. This requires at least 8 digits in the
ARS table (Program 26-02-01).
●
2 - Delete the leading digit if dialed as part of the initial call. This requires at least 8 digits
in the ARS table (Program 26-02-01).
● 1 - Add a leading 1 if not dialed as part of the initial call. This requires at least 8 digits in
the ARS table (Program 26-02-01).
●
INPA - Insert the NPA speci Þ ed by NPA.
●
DNN - Outdial the NN number of digits or execute the code that follows. For example,
D041234 out-dials 124. Valid entries are 0-9, #, *, Wnn (wait nn seconds) and P (pause).
Each digits code counts as a digit. So for example, if a P was added for a pause, the entry
would look like: D05P1234. This Dial Treatment can only be added from telephone pro-
gramming.
●
Wnn - Wait nn seconds.
●
P - Pause in analog trunk.
●
R - Redial the initially dialed number, including any modi Þ cations
●
E - End of Dial Treatment. All Dial Treatments must end with the E code.
●
X - When ARS is enabled, X must be entered in the Dial Treatment in order for the system to
output the extension number of the call’s originator to the black box for the E911 feature.
● An - Alternate Carrier Access (n = 1 ~ 4). The numeric digit instructs the system to insert
a Transit Network Selection information element in the SETUP message and also identi-
Þ es which code in Program 26-11 will be included in the information element.
➻
44-01-01 : System Options for ARS/F-Route - ARS/F-Route Time Schedule
Set this option to ‘0’ so that the F-Route table selected is determined only by the digits dialed
without any relation to the day or time of the call.
➻
44-02-01 : Dial Analysis Table for ARS/F-Route Access - Dial
Set the number of digits to be analyzed by the system for ARS routing. Using the 4-digit
extension number example in Program 11-01-01, the entry would be: Analysis Table 1:
720@@; Analysis Table 2: 723@@.
➻
44-02-02 : Dial Analysis Table for ARS/F-Route Access - Service Type
Select the Service Type (0=no setting, 1=extension call, 2=ARS/F-Route table, 3=Dial extension
analyze table). Using the 4-digit extension number example in Program 11-01-01, the entry would
be: Analysis Table 1: 2 (ARS/F-Route table); Analysis Table 2: 2 (ARS/F-Route table).
➻
44-02-03 : Dial Analysis Table for ARS/F-Route Access - Additional Data
Enter the additional data required for the service type selected in Program 44-02-02, either the
number of digits to be deleted or the table number to be used. Using the 4-digit extension
number example in Program 11-01-01, the entry would be: 1 (delete 1 digit).
➻
44-02-04 : Dial Analysis Table for ARS/F-Route Access - Dial Tone Simulation
If enabled (1), this option sends dial tone to the calling party once the routing is determined.
This may be required if the central of
Þ ce at the destination does not send dial tone. Using the
4-digit extension number example in Program 11-01-01, the entry would be: 0 (disabled).