background image

Extron • System 4

xi

xi

xi

xi

xi

 Switcher Series • User’s Manual • P/N 68-413-02 Rev. E

NEC Installation

Configuration and Connections

(Note: Information depends on
System 4

xi

 setup.)

(See note.)

(See note.)

(See note.)

(See note.)

[System 4

xi

 model and software

version displayed here]

Page 2

}

SW1

ON

SW2

SW4

SW3

SW5

J9

3

4

1

2

Connecting System 4

xi

xi

xi

xi

xi

 to NEC/Runco or NEC XG Projector

If the System 4

xi

 is already configured for an NEC/Runco or NEC XG projector,

go to step 4. If it is not set up correctly, it will be necessary to change switch
settings on the System 4

xi 

’s Main Controller Board. Begin at Step 1 to verify the

correct configuration.

1. Use the Front Panel to display the Information Menu to verify that the System 4

xi

is already set up for the NEC/Runco or NEC XG projector. Apply power to the
System 4

xi

 and do the following:

a. Press 

 to display the M

ENU

 S

ELECT

 on the LCD screen.

b. Press 

 or 

 to step to Menu 8.

c. Press 

 to select this menu.

d. Press 

 or 

 to display the configuration. The example to the left is general,

yours will show the System 4

xi

 model name, the software version and the

following information:
PRJ = NEC  (

or NEC_XG for XG model)

PRJ BAUD = 9600
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)

2. Go to the procedure on page 2-3 to remove the System 4

xi

 cover and then go to

page 2-4 to set up the Main Controller board. Return to Step 3 (below) when the
configuration is correct.

Config

Projector

SW1: 1-2-3-4 SW2

SW3

SW4

SW5

SW6

Prj Cable

Comm

as

Adapter

NEC/Runco

off-on-on-off

0

0

7

5

0

J9

26-472-01

NEC XG

off-on-on-off

0

0

4

F

0

J9

26-472-01

System 4xi to NEC/Runco Configuration

System 4xi to NEC XG Configuration

3. Double-check your work and be sure the System 4

xi

 cover is on securely.

4. Install the System 4

xi

 in its place of operation (i.e. rack), but not powered on.

__________ Changes in some switch configurations are not detected until the power is

removed at the AC cord, and then restored.
If the Projector Cable is wrongly connected to J15 on the Main Controller Board,
Menu 8 will not indicate the error.

Use the appropriate cable diagram on page 6 and continue.

5. The NEC Adapter (NC COM) has two male connectors, one 9-pin and one

15-pin. Plug the 15-pin male connector to the female connector marked
“Remote 1” on the NEC connector panel.

SW1

ON

SW2

SW4

SW3

SW5

J9

3

4

1

2

Содержание 4xi NEC













Отзывы: