Neat INKA Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 36

Neat INKA Скачать руководство пользователя страница 19

INKA, IOR, REPO & LINK

2.2.6 Transmission Delay

The

transmission delay

can be configured by setting jumpers J4 and J5 in REPO.

See section 3.4.6 for details.

J4 J5

Transmission

Delay

OFF OFF 2.5

seconds

OFF ON 5.0

seconds

ON OFF

7.5

seconds

ON ON

10.0

seconds

2.2.7 Output Mode

The

output mode

can be configured by setting jumpers J4 and J5 in IOR and LINK.

See section 3.3 for details.

J4 J5

Output

Mode

OFF OFF Pulse

mode

OFF ON Toggle

mode

ON OFF

Static

mode

Static mode

means that the relay never changes state, unless a special maneuver message is

received from, for example, home care phone NEO.

2.2.8 Power Mode

The

power mode

can be configured by setting jumpers J6 in INKA and IOR.

See section 3.5 for details.

Jumper Power Source ON (mounted)

OFF (not mounted)

AC/DC
adapter

Normal power
mode

Normal power mode

J6

Batteries only

Normal power
mode

Power save mode

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0

19

«
...
17
18
19
20
21
...
»

Содержание INKA





































Отзывы:

Нет отзывов