NCS NCS-C250C Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

background image

12.1 Option Board Basic Setup

The COR/Hookswitch Option Board must be installed at the factory. In addition to the COR &
Hookswitch Options, the board provides extension pins for the MIC Z, Electret Voltage and Front
Panel Mic Connector pins from the main C250C board. See the diagram below:

Refer to Section 7 of this Manual for instructions on setting these jumpers. Note that the 200
Ohm jumper position is incorrectly marked on this board. The correct position for 200 Ohms is
the two pins next to the label “J10”.

Option Board

NCS-C250C Instruction Manual Rev J

Copyright © 2004-2010 New Communications Solutions, LLC

21

Mic Impedance
Jumper Block

Electret Voltage
Jumper

Front Panel Mic
Connector Pins

«
...
19
20
21
22
23
...
»

Содержание NCS-C250C





























Отзывы:

Нет отзывов

Похожие инструкции для NCS-C250C

Бренд: ABB Страницы: 7

Бренд: Kathrein Страницы: 8

Бренд: Nayar Systems Страницы: 21

Бренд: Kathrein Страницы: 24

Бренд: Kasia Страницы: 5

Temperature SWICHGAGE SPL

Бренд: Murphy Страницы: 4

Бренд: Edimax Страницы: 2

ZigBee Mini Hub

Бренд: ORVIBO Страницы: 3

Бренд: Comtrend Corporation Страницы: 2

Бренд: Zamel Страницы: 4

Бренд: e+p Страницы: 2

Бренд: IPGARD Страницы: 2

START-LINE AGC-3500

Бренд: Trust Страницы: 16

FortiSwitch 424E Series

Бренд: Fortinet Страницы: 11

Бренд: PTN Страницы: 44

Бренд: Edimax Страницы: 2

Бренд: Cable Electronics Страницы: 12

Signal Distribution Box SDB45

Бренд: Audiovox Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды